Back to AD

AD 91-16-08 ACTIVE

Auxiliary Fuel System
Key Information
AD Number 91-16-08 Status Active
Effective Date September 06, 1991 Issue Date Not specified
Docket Number 90-NM-236-AD Amendment 39-7098
Product Type ["Aircraft"] Product Subtype ["Large Airplane"]
CFR Part --- - Part 39 CFR Section N/A
Citation This information is not available.
Applicability
Manufacturer(s) The Boeing Company
Model(s) 737-100 Series 737-200 Series 737-200C Series 737-300 Series 737-400 Series 737-500 Series 737-600 Series 737-700 Series 737-800 Series
Regulatory Text

91-16-08 BOEING: Amendment 39-7098. Docket No. 90-NM-236-AD.\n \n\tApplicability: Model 737 series airplanes, equipped with a Boeing aft cargo bay auxiliary fuel tank; listed in Boeing Service Bulletin 737-28-1088, dated September 6, 1990; certificated in any category. \n\n\tCompliance: Required as indicated, unless previously accomplished. \n\n\tTo reduce the potential for a fire in the aft cargo compartment due to fuel leaking from the auxiliary fuel tank, accomplish the following: \n\n\tA.\tWithin 90 days after the effective date of this AD, accomplish one of the following: \n\n\t\t1.\tDeactivate the auxiliary fuel system and attach a placard in the flight compartment to indicate that the auxiliary fuel tank is inoperative, in accordance with Boeing Alert Service Bulletin 737-28A1034, Revision 2, dated December 6, 1990, or Boeing Service Bulletin 737-28-1088, dated September 6, 1990; or \n\n\t\t2.\tInstall a check valve and a pressure activated shutoff valve in the auxiliary fuel systemnear the center wing tank in accordance with Boeing Alert Service Bulletin 737-28A1034, Revision 2, dated December 6, 1990; and perform the following inspections of the auxiliary fuel tank support structure in accordance with the inspection procedures below: \n\n\t\t\ta.\tWithin 500 flight cycles after the effective date of this AD, to detect a disbonded or cracked side panel in the auxiliary fuel tank, accomplish one of the following: \n\n\t\t\t\t(1)\tConduct an inspection of the lower sidewall (curved) panels of the auxiliary fuel tanks for disbonding, in accordance with Part I of the Accomplishment Instructions in Boeing Service Bulletin 737-28-1088, dated September 6, 1990. \n\n\t\t\t\t(2)\tPerform a leak check of the auxiliary fuel tanks in accordance with Part III of Boeing Service Bulletin 737-28-1088, dated September 6, 1990. If any fuel leakage is detected, repair prior to further flight in accordance with Part III of the service bulletin. Repeat leak check prior to each flight. \n\n\t\t\tb.\tWithin 12,000 flight cycles after the effective date of this AD, conduct an inspection of the auxiliary fuel tank and support structure in accordance with Part II of Boeing Service Bulletin 737- 28-1088, dated September 6, 1990. Repeat this inspection at intervals not to exceed 12,000 flight cycles. Accomplishment of this inspection constitutes terminating action for the inspection requirements of paragraph A.2.a. of this AD. \n\n\t\t\tc.\tIf a disbonded or cracked panel is detected during the inspections required by paragraphs A.2.a. or A.2.b. of this AD, accomplish one of the following prior to further flight: \n\n\t\t\t\t(1)\tReplace the panel in accordance with Part IV of Boeing Service Bulletin 737-28-1088, dated September 6, 1990; or \n\n\t\t\t\t(2)\tDeactivate the auxiliary fuel tank in accordance with Boeing Alert Service Bulletin 737-28A1034, Revision 2, dated December 6, 1990; or Boeing Service Bulletin 737-28-1088, dated September 6, 1990; or \n\n\t\t\t\t(3)\tRemove the auxiliary fuel tankin accordance with the Boeing 737 Maintenance Manual Subject 28-14-0. \n\n\tNOTE: A deactivated auxiliary fuel tank will require inspections per paragraph A.2. of this AD when reactivated. Auxiliary fuel tanks that are deactivated but remain in an airplane accumulate the same number of flight cycles as the airplane. \n\n\tB.\tAuxiliary fuel tanks currently not installed in an airplane must be inspected in accordance with Boeing Service Bulletin 737-28-1088, dated September 6, 1990, prior to installation in an airplane if they have accumulated more than 4,000 flight cycles. If any cracking or delamination is detected, repair prior to installation in an airplane. \n\n\tC.\tAn alternative method of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA, Transport Airplane Directorate. \n\n\tNOTE: The request should be forwarded through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Seattle ACO. \n\n\tD.\tSpecial flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD. \n\n\tAll persons affected by this directive who have not already received the appropriate service documents from the manufacturer may obtain copies upon request to Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington 98124. These documents may be examined at the FAA, Northwest Mountain Region, Transport Airplane Directorate, 1601 Lind Avenue S.W., Renton, Washington. \n\n\tThis amendment (39-7098, AD 91-16-08) becomes effective on September 6, 1991.