| AD Number | 80-12-13 | Status | Active |
| Effective Date | July 14, 1980 | Issue Date | Not specified |
| Docket Number | Unknown | Amendment | 39-3799 |
| Product Type | ["Aircraft"] | Product Subtype | ["Large Airplane"] |
| CFR Part | --- - Part 39 | CFR Section | N/A |
| Citation | This information is not available. | ||
| Manufacturer(s) | Not specified |
| Model(s) | BH.125 Series 400A BH.125 Series 600A DH.125 Series 1A DH.125 Series 1A/R-522 DH.125 Series 1A/S-522 DH.125 Series 1A-522 DH.125 Series 3A DH.125 Series 3A/R DH.125 Series 3A/RA DH.125 Series 400A HS.125 Series 600A HS.125 Series 700A |
80-12-13 BRITISH AEROSPACE (formerly Hawker Siddeley, Ltd.): Amendment 39- 3799. Applies to Model DH/BH/HS 125 series airplanes, certificated in all categories, which have incorporated British Aerospace modification 251605 and have any of the following: an AiResearch APU Model GTCP30-92(c) installed as a replacement for AiResearch APU Model GTCP3-92, AiResearch Service Bulletin 30-49-3689 incorporated, or British Aerospace modification 257513, 252502, 256817, 256855, 258015, 258027, or 258037 incorporated.
NOTE: This AD is known to apply, but is not necessarily limited, to the airplanes listed below.
Model
Series - all variants
Serial Number
DH/HS 125
1
25/097
DH/HS 125
3
25/113, 117, 125, 133,
140, 143, 144, 154, 157,
162, 164 thru 168, 172
HS/BH 125
400, 401, 403
25/178, 189, 194, 197,
209, 215, 217, 227, 231,
240, 242, 243, 246 thru 251,
254, 257, 270, 271, 272, 274
HS/BH 125
600
25/256 & 25/6012, 6015,
6017, 6019, 6021, 6024,
6027, 6029, 6030, 6031,
6033, 6035, 6037, 6039,
6041, 6042, 6045, 6048,
6049, 6050, 6052, 6053,
6054, 6056, 6057, 6058,
6059, 6060, 6062, thru 6071
HS 125
700
25/7001, 7007, 7010,
7013, 7020, 7022, 7025,
7028, 7031, NA 0201 0218
Compliance is required as indicated, unless already accomplished.
To prevent failure of the main engine mount beam, accomplish the following:
(a) Within the next 500 hours time in service after the effective date of this AD, modify the main engine mount beam in accordance with Section 2, "Accomplishment Instructions", British Aerospace Service Bulletin 49-28(2675), Rev. 2, dated June 26, 1979, (hereinafter referred to as the Service Bulletin) or an FAA-approved equivalent.
(b) For purposes of this AD, with the exception of cleats equivalent to those specified in the Service Bulletin, an FAA-approved equivalent may be approved by an FAA airworthiness or engineering and manufacturing inspector or the Chief, Aircraft Certification Staff, FAA, Europe, Africa, and Middle East Office. Any cleats equivalent to those specified in the Service Bulletin must be approved by the Chief, Aircraft Certification Staff, FAA Europe, Africa, and Middle East Office.
(c) Upon request of an operator, the Chief, Aircraft Certification Staff, FAA, Europe, Africa and Middle East Office, c/o American Embassy, Brussels, Belgium, may adjust the compliance time specified in paragraph (a) of this AD or approve a modification equivalent to that specified in the Service Bulletin provided such request is made through an FAA maintenance inspector and the request contains substantiating data to justify the request for that operator.
This amendment becomes effective July 14, 1980.