AD 98-13-37 SUPERSEDED

This amendment adopts a new airworthiness directive (AD), applicable to certain Airbus Model A300 and all Model A300-600 series airplanes, that requires a one-time inspection for cracking of the gantry lower flanges in the main landing gear (MLG) bay area; and repair, if necessary. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to detect and correct cracking of the gantry lower flanges in the MLG bay area, which could result in decompression of the airplane.

Final rule.

98-13-37 AIRBUS INDUSTRIE: Amendment 39-10628. Docket 98-NM-81-AD.

Applicability: Model A300 series airplanes on which Airbus Modification 3474 has been accomplished, and all Model A300-600 series airplanes; certificated in any category.

NOTE 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been otherwise modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.Compliance: Required as indicated, unless accomplished previously.

To detect and correct cracking of the gantry lower flanges in the main landing gear (MLG) bay area, which could result in decompression of the airplane, accomplish the following:

(a) Prior to the accumulation of 16,300 total flight cycles, or within 500 flight cycles after the effective date of this AD, whichever occurs later, perform a one-time ultrasonic inspection for cracking of the gantry lower flanges in the MLG bay area, in accordance with Airbus All Operators Telex (AOT) 53-11, dated October 13, 1997.

(1) If any cracking is detected, prior to further flight, repair in accordance with the AOT.

(2) If no cracking is detected, no further action is required by this AD.

(b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate.Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116.

NOTE 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116.

(c) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished.

(d) The inspection and repair shall be done in accordance with Airbus All Operators Telex (AOT) 53-11, dated October 13, 1997. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Airbus Industrie, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

NOTE 3: The subject of this AD is addressed in French airworthiness directive 97-372- 236(B), dated December 3, 1997.

(e) This amendment becomes effective on July 30, 1998.

A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to certain Airbus Model A300 and all Model A300-600 series airplanes was published in the Federal Register on April 21, 1998 (63 FR 19684). That action proposed to require a one-time inspection for cracking of the gantry lower flanges in the main landing gear (MLG) bay area; and repair, if necessary.

Comments
Interested persons have been afforded an opportunity to participate in the making of this amendment. Due consideration has been given to the single comment received.

The commenter supports the proposed rule.

Conclusion
After careful review of the available data, including the comment noted above, the FAA has determined that air safety and the public interest require the adoption of the rule as proposed.

Interim Action
This is considered to be interim action until final action is identified, atwhich time the FAA may consider further rulemaking.

Cost Impact
The FAA estimates that 67 airplanes of U.S. registry will be affected by this AD. It will take approximately 4 work hours per airplane to accomplish the required inspection, at an average labor rate of $60 per work hour. Based on this figure, the cost impact of the inspection required by this AD on U.S. operators is estimated to be $16,080, or $240 per airplane.

The cost impact figure discussed above is based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted.

Regulatory Impact
The regulations adopted herein will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612,it is determined that this final rule does not have sufficient federalism implications to warrant the preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption "ADDRESSES."

List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39 - AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
39.13 [Amended]
2. Section 39.13 is amended by adding the following new airworthiness directive:

The service information referenced in this AD may be obtained from Airbus Industrie, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France. This information may be examined at the Federal Aviation Administration (FAA), Transport Airplane Directorate, Rules Docket, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

Norman B. Martenson, Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425) 227-2110; fax (425) 227-1149.