AD 2021-02-18 ACTIVE

The FAA is adopting a new airworthiness directive (AD) for all Airbus Defense and Space S.A. Model CN-235, CN-235-100, CN-235-200, and CN-235-300 airplanes and Model C-295 airplanes. This AD was prompted by cracks found on certain left- and right-hand stringers in a certain area of the fuselage. This AD requires repetitive inspections for cracking or broken rivets of certain left- and right-hand stringers and surrounding structure, and repair if necessary, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.

Final rule.

Adoption of the Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive: \n\n2021-02-18 Airbus Defense and Space S.A. (Formerly Known as Construcciones Aeronauticas, S.A.): Amendment 39-21401; Docket No. FAA-2020-1020; Project Identifier MCAI-2020-00988-T. \n\n(a) Effective Date \n\n\n\tThis airworthiness directive (AD) is effective March 30, 2021. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\tThis AD applies to all Airbus Defense and Space S.A. Model CN- 235, CN-235-100, CN-235-200, and CN-235-300 airplanes and Model C- 295 airplanes, certificated in any category. \n\n(d) Subject \n\n\n\tAir Transport Association (ATA) of America Code 53, Fuselage. \n\n(e) Reason \n\n\n\tThis AD was prompted by cracks found on certain left- and right- hand stringers in the area of frame (FR) 43 of the fuselage. The FAA is issuing this AD to address such cracking in the stringers, which could result in reduced structural integrity of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Requirements \n\n\n\tExcept as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2020-0159, dated July 16, 2020 (EASA AD 2020-0159). \n\n(h) Exceptions to EASA AD 2020-0159 \n\n\n\t(1) Where EASA AD 2020-0159 refers to its effective date, this AD requires using the effective date of this AD. \n\t(2) The ''Remarks'' section of EASA AD 2020-0159 does not apply to this AD. \n\t(3) Where EASA AD 2020-0159 lists a compliance time of ''during the next A-check, or within 300 FH (flight hours) after the effective date of this AD, whichever occurs later,'' this AD requires using a compliance time of within 300 FH after the effective date of this AD. \n\n(i) No Reporting Requirement \n\n\n\tAlthough the service information referenced in EASA AD 2020-0159 specifies to submit certain information to the manufacturer, this AD does not include that requirement. \n\n(j) Other FAA AD Provisions \n\n\n\tThe following provisions also apply to this AD: \n\t(1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. \n\t(2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus Defense and Space S.A.'s EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. \n\n(k) Related Information \n\n\n\tFor more information about this AD, contact Shahram Daneshmandi, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231-3220; email shahram.daneshmandi@faa.gov. \n\n(l) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. \n\t(i) European Union Aviation Safety Agency (EASA) AD 2020-0159, dated July 16, 2020. \n\t(ii) (Reserved) \n\t(3) For EASA AD 2020-0159, contact the EASA, Konrad-Adenauer- Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. \n\t(4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. This material may be found in the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020-1020. \n\t(5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html. \n\n\n\tIssued on January 14, 2021. Ross Landes, Deputy Director for Regulatory Operations, Compliance & Airworthiness Division, Aircraft Certification Service. (FR Doc. 2021-03570 Filed 2-22-21; 8:45 am) BILLING CODE 4910-13-P

Discussion \n\n\n\tThe EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2020-0159, dated July 16, 2020 (EASA AD 2020-0159) (also referred to as the Mandatory Continuing Airworthiness Information, or the MCAI), to correct an unsafe condition for all Airbus Defense and Space S.A. Model CN-235, CN-235-100, CN-235- 200, and CN-235-300 airplanes and Model C-295 airplanes. \n\tThe FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all Airbus Defense and Space S.A. Model CN-235, CN-235-100, CN-235-200, and CN-235-300 airplanes and Model C-295 airplanes. The NPRM published in the Federal Register on November 10, 2020 (85 FR 71583). The NPRM was prompted by cracks found on certain left- and right-hand stringers in a certain area of the fuselage. The NPRM proposed to require repetitive inspections for cracking or broken rivets of certain left- and right- handstringers and surrounding structure, and repair if necessary, as specified in an EASA AD. \n\tThe FAA is issuing this AD to address such cracking in the stringers, which could result in reduced structural integrity of the airplane. See the MCAI for additional background information. \n\nComments \n\n\n\tThe FAA gave the public the opportunity to participate in developing this final rule. The FAA received no comments on the NPRM or on the determination of the cost to the public. \n\nConclusion \n\n\n\tThe FAA reviewed the relevant data and determined that air safety and the public interest require adopting this final rule as proposed, except for minor editorial changes. The FAA has determined that these minor changes: \n\tAre consistent with the intent that was proposed in the NPRM for addressing the unsafe condition; and \n\tDo not add any additional burden upon the public than was already proposed in the NPRM. \n\nRelated Service Information Under 1 CFR Part 51 \n\n\n\tEASA AD 2020-0159 describes procedures for repetitive detailed visual (DET) or high frequency eddy current inspections of the stringer P0a and P0a' at the riveted line of the attachment to the gusset and along the stringer head, in particular at the area of the last attachment of the gusset to the stringer in the midpoint between frame (FR) 43 and FR44, repetitive DET inspections for fatigue cracks of the fuselage skin, along the stringers' footprint and surrounding structure and the attachment of the gusset to the FR43; repetitive DET inspections for fatigue cracks of the actuator bracket on FR43, along the radius of the vertical nerves, inner lug holes, and attachment holes of the bracket to FR43; repetitive DET inspections for fatigue cracks or broken rivets in the web and joint clips to skin and stringer of both sides of the frame between stringer P1d and P1d' (two stringers for each side from the central stringer P0a); repetitive DET inspections for fatigue cracks or broken rivets of the gussets, along the flange which joins FR43; and repair of any cracking or broken rivets. \n\tThis material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. \n\nInterim Action \n\n\n\tThe FAA considers this AD interim action. If final action is later identified, the FAA might consider further rulemaking then. \n\nCosts of Compliance \n\n\n\tThe FAA estimates that this AD affects 8 airplanes of U.S. registry. The FAA estimates the following costs to comply with this AD: \n\n\n\tEstimated Costs for Required Actions ---------------------------------------------------------------------------------------------------------------- \n\tCost per Cost on U.S. \n\tLabor cost Parts cost product operators ---------------------------------------------------------------------------------------------------------------- 2 work-hours x $85 per hour = $170........................... $0 $170 $1,360 ---------------------------------------------------------------------------------------------------------------- \n\n\n\tThe FAA has received no definitive data that enables providing cost estimates for the on-condition action specified in this AD. \n\nAuthority for This Rulemaking \n\n\n\tTitle 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. \n\tThe FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in aircommerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. \n\nRegulatory Findings \n\n\n\tThis AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. \n\tFor the reasons discussed above, I certify that this AD: \n\n((Page 10742)) \n\n\n\t(1) Is not a ''significant regulatory action'' under Executive Order 12866, \n\t(2) Will not affect intrastate aviation in Alaska, and \n\t(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. \n\nList of Subjects in 14 CFR Part 39 \n\n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of March 30, 2021. \nADDRESSES: For material incorporated by reference (IBR) in this AD, contact the EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this IBR material on the EASA website at https://ad.easa.europa.eu You may view this IBR material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. It is also available in the AD docket on the internet at https:// \n\n((Page 10741)) \n\nwww.regulations.gov by searching for and locating Docket No. FAA-2020- 1020. \n\nExamining the AD Docket \n\n\n\tYou may examine the AD docket on the internet at https://www.regulations.gov by searching for and locating Docket No. FAA-2020- 1020;or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

Shahram Daneshmandi, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax 206-231- 3220; email shahram.daneshmandi@faa.gov.