AD 2025-18-07 ACTIVE

The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-600, B4-600R, and F4-600R series airplanes; and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is issuing this AD to address the unsafe condition on these products.

Final rule.

1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2025-18-07 Airbus SAS: Amendment 39-23134; Docket No. FAA-2025-0472; Project Identifier MCAI-2024-00738-T. (a) Effective Date This airworthiness directive (AD) is effective October 23, 2025. (b) Affected ADs This AD affects AD 2018-18-21, Amendment 39-19400 (83 FR 47054, September 18, 2018) (AD 2018-18-21). (c) Applicability This AD applies to all Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category. (1) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes. (2) Model A300 B4-605R and B4-622R airplanes. (3) Model A300 C4-605R Variant F airplanes. (4) Model A300 F4-605R and F4-622R airplanes. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address the risks associated with the effects of aging on airplane systems. The unsafe condition, if not addressed, could result in an increased potential for failure of certain life-limited parts, and reduced structural integrity or controllability of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2024-0238, dated December 10, 2024 (EASA AD 2024-0238). (h) Exceptions to EASA AD 2024-0238 (1) This AD does not adopt the requirements specified in paragraph (1) of EASA AD 2024-0238. (2) Paragraph (2) of EASA AD 2024-0238 specifies revising "the approved AMP" within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (2) of EASA AD 2024-0238 is at the applicable "limitations" as incorporated by the requirements of paragraph (2) of EASA AD 2024-0238, or within 90 days after the effective date of this AD, whichever occurs later. (4) This AD does not adopt the provisions specified in paragraph (3) of EASA AD 2024-0238. (5) This AD does not adopt the "Remarks" section of EASA AD 2024-0238. (i) Provisions for Alternative Actions and Intervals After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions ( e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the "Ref. Publications" section of EASA AD 2024-0238. (j) Terminating Action for Certain Tasks Required by AD 2018-18-21 For the airplanes identified in paragraph (c) of this AD only: Accomplishing the actions required by this AD terminates the corresponding requirements of AD 2018-18-21 for the tasks identified in the material referenced in EASA AD 2024-0238 only. (k) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (l) of this AD and email to: AMOC@faa.gov . Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR 520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (l) Additional Information For more information about this AD, contact James Clary, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 817-222-5138; email: James.Clary@faa.gov . (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2024-0238, dated December 10, 2024. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu . You may find this material on the EASA website at ad.easa.europa.eu . (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email fr.inspection@nara.gov . Issued on September 4, 2025. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service. [FR Doc. 2025-18086 Filed 9-17-25; 8:45 am]BILLING CODE 4910-13-P

Background The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all Airbus SAS Model A300-600 series airplanes. The NPRM was published in the Federal Register on March 25, 2025 (90 FR 13558). The NPRM was prompted by AD 2024-0238, dated December 10, 2024 (EASA AD 2024-0238) (also referred to as the MCAI), issued by EASA, which is the Technical Agent for the Member States of the European Union. The MCAI states that new or more restrictive airworthiness limitations have been developed. In the NPRM, the FAA proposed to require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in EASA AD 2024-0238. The FAA is issuing this AD to address the risks associated with the effects of aging on airplane systems. You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA-2025-0472. Discussion of Final Airworthiness Directive Comments The FAA received a comment from Air Line Pilots Association, International (ALPA) who supported the NPRM without change. Conclusion These products have been approved by the civil aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, that authority has notified the FAA of the unsafe condition described in the MCAI referenced above. The FAA reviewed the relevant data, considered any comments received, and determined that air safety requires adopting this AD as proposed. Accordingly, the FAA is issuing this AD to address the unsafe condition on these products. Except for minor editorial changes, this AD is adopted as proposed in the NPRM. None of the changes will increase the economic burden on any operator. Material Incorporated by Reference Under 1 CFR Part 51 The FAA reviewed EASA AD 2024-0238, which specifies procedures for new or more restrictive airworthiness limitations for airplane structures and safe life limits. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. Costs of Compliance The FAA estimates that this AD affects 128 airplanes of U.S. registry. The FAA estimates the following costs to comply with this AD: The FAA has determined that revising the existing maintenance or inspection program takes an average of 90 work-hours per operator, although the agency recognizes that this number may vary from operator to operator. Since operators incorporate maintenance or inspection program changes for their affected fleet(s), the FAA has determined that a per-operator estimate is more accurate than a per-airplane estimate. Therefore, the agency estimates the average total cost per operator to be $7,650 (90 work-hours × $85 per work-hour). Authority for This Rulemaking Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a "significant regulatory action" under Executive Order 12866, (2) Will not affect intrastate aviation in Alaska, and (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39-AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by adding the following new airworthiness directive: 2025-18-07 Airbus SAS: Amendment 39-23134; Docket No. FAA-2025-0472; Project Identifier MCAI-2024-00738-T. (a) Effective Date This airworthiness directive (AD) is effective October 23, 2025. (b) Affected ADs This AD affects AD 2018-18-21, Amendment 39-19400 (83 FR 47054, September 18, 2018) (AD 2018-18-21). (c) Applicability This AD applies to all Airbus SAS airplanes identified in paragraphs (c)(1) through (4) of this AD, certificated in any category. (1) Model A300 B4-601, B4-603, B4-620, and B4-622 airplanes. (2) Model A300 B4-605R and B4-622R airplanes. (3) Model A300 C4-605R Variant F airplanes. (4) Model A300 F4-605R and F4-622R airplanes. (d) Subject Air Transport Association (ATA) of America Code 05, Time Limits/Maintenance Checks. (e) Unsafe Condition This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. The FAA is issuing this AD to address the risks associated with the effects of aging on airplane systems. The unsafe condition, if not addressed, could result in an increased potential for failure of certain life-limited parts, and reduced structural integrity or controllability of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2024-0238, dated December 10, 2024 (EASA AD 2024-0238). (h) Exceptions to EASA AD 2024-0238 (1) This AD does not adopt the requirements specified in paragraph (1) of EASA AD 2024-0238. (2) Paragraph (2) of EASA AD 2024-0238 specifies revising "the approved AMP" within 12 months after its effective date, but this AD requires revising the existing maintenance or inspection program, as applicable, within 90 days after the effective date of this AD. (3) The initial compliance time for doing the tasks specified in paragraph (2) of EASA AD 2024-0238 is at the applicable "limitations" as incorporated by the requirements of paragraph (2) of EASA AD 2024-0238, or within 90 days after the effective date of this AD, whichever occurs later. (4) This AD does not adopt the provisions specified in paragraph (3) of EASA AD 2024-0238. (5) This AD does not adopt the "Remarks" section of EASA AD 2024-0238. (i) Provisions for Alternative Actions and Intervals After the existing maintenance or inspection program has been revised as required by paragraph (g) of this AD, no alternative actions ( e.g., inspections) and intervals are allowed unless they are approved as specified in the provisions of the "Ref. Publications" section of EASA AD 2024-0238. (j) Terminating Action for Certain Tasks Required by AD 2018-18-21 For the airplanes identified in paragraph (c) of this AD only: Accomplishing the actions required by this AD terminates the corresponding requirements of AD 2018-18-21 for the tasks identified in the material referenced in EASA AD 2024-0238 only. (k) Additional AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, AIR-520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the manager of the Continued Operational Safety Branch, send it to the attention of the person identified in paragraph (l) of this AD and email to: AMOC@faa.gov . Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the responsible Flight Standards Office. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, AIR 520, Continued Operational Safety Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (l) Additional Information For more information about this AD, contact James Clary, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 817-222-5138; email: James.Clary@faa.gov . (m) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference of the material listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this material as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2024-0238, dated December 10, 2024. (ii) [Reserved] (3) For EASA material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu . You may find this material on the EASA website at ad.easa.europa.eu . (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, visit www.archives.gov/federal-register/cfr/ibr-locations, or email fr.inspection@nara.gov . Issued on September 4, 2025. Peter A. White, Deputy Director, Integrated Certificate Management Division, Aircraft Certification Service.

AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA-2025-0472; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. Material Incorporated by Reference: - For European Union Aviation Safety Agency (EASA) material identified in this AD, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu . You may find this material on the EASA website at ad.easa.europa.eu . - You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. It is also available at regulations.gov under Docket No. FAA-2025-0472.

James Clary, Aviation Safety Engineer, FAA, 2200 South 216th St., Des Moines, WA 98198; phone: 817-222-5138; email: James.Clary@faa.gov .