Back to AD

AD 2021-15-05 SUPERSEDED

Engine Controls
WARNING: This AD has been superseded and is no longer active. Replaced by: 2025-07-10. Refer to the superseding AD(s) for current requirements.
Key Information
AD Number 2021-15-05 Status Superseded
Effective Date September 13, 2021 Issue Date July 09, 2021
Docket Number FAA-2021-0347 Amendment 39-21652
Product Type ["Engine"] Product Subtype ["Large Airplane"]
CFR Part --- - Part 39 CFR Section N/A
Citation (Federal Register Volume 86, Number 150 (Monday, August 9, 2021))
Applicability
Manufacturer(s) General Electric Company
Model(s) GE90-110B1 GE90-115B
Related Airworthiness Directives
Superseded By 2025-07-10
Summary

The FAA is adopting a new airworthiness directive (AD) for all General Electric Company (GE) GE90-110B1 and GE90-115B model turbofan engines. This AD was prompted by an in-service occurrence of loss of engine thrust control resulting in uncommanded high thrust. This AD requires initial and repetitive replacement of the full authority digital engine control (FADEC) integrated circuit (MN4) microprocessor. The FAA is issuing this AD to address the unsafe condition on these products.

Action Required

Final rule.

Regulatory Text

The Amendment \n\n\n\tAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n0 1. The authority citation for part 39 continues to read as follows: \n\n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n\n\nSec. 39.13 (Amended) \n\n0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive: \n\n2021-15-05 General Electric Company: Amendment 39-21652; Docket No. FAA-2021-0347; Project Identifier AD-2020-01610-E. \n\n(a) Effective Date \n\n\n\tThis airworthiness directive (AD) is effective September 13, 2021. \n\n(b) Affected ADs \n\n\n\tNone. \n\n(c) Applicability \n\n\n\tThis AD applies to General Electric Company (GE) GE90-110B1 and GE90-115B model turbofan engines. \n\n(d) Subject \n\n\n\tJoint Aircraft System Component (JASC) Code 7600, Engine Controls. \n\n(e) Unsafe Condition \n\n\n\tThis AD was prompted by an in-service occurrence of loss of engine thrust control resulting in uncommanded high thrust. The FAA is issuing this AD to prevent failure of the full authority digital engine control (FADEC) integrated circuit (MN4) microprocessor solder ball. The unsafe condition, if not addressed, could result in loss of engine thrust control and reduced control of the airplane. \n\n(f) Compliance \n\n\n\tComply with this AD within the compliance times specified, unless already done. \n\n(g) Required Actions \n\n\n\t(1) Within the following compliance times after the effective date of this AD, replace the FADEC MN4 microprocessor using an approved overhaul procedure: \n\t(i) For a FADEC MN4 microprocessor with 10,500 or more cycles since new (CSN), replace the FADEC MN4 microprocessor before accumulating 500 additional cycles on the FADEC MN4 microprocessor. \n\t(ii) For a FADEC MN4 microprocessor with 5,000 CSN or more, but fewer than 10,500 CSN, replace the FADEC MN4 microprocessor at the next FADEC component shop visit or before accumulating 11,000 CSNon the FADEC MN4 microprocessor, whichever occurs first. \n\t(2) Thereafter, repeat the replacement of the FADEC MN4 microprocessor at the first FADEC component shop visit after accumulating 5,000 CSN since the last replacement but before accumulating 11,000 CSN since the last replacement. \n\n((Page 43411)) \n\n(h) Definition \n\n\n\t(1) For the purpose of this AD, an ''approved overhaul procedure'' is one of the following: \n\t(i) Replacement of the FADEC MN4 microprocessor using FADEC International-approved maintenance procedures; or \n\t(ii) Replacement of the FADEC MN4 microprocessor using the Accomplishment Instructions, paragraph 3.A., of GE GE90-100 Service Bulletin 73-0118, Revision 01, dated April 27, 2021. \n\t(2) For the purpose of this AD, a ''FADEC component shop visit'' is the induction of the FADEC into a repair facility to perform internal maintenance on the FADEC. \n\n(i) Alternative Methods of Compliance (AMOCs) \n\n\n\t(1) The Manager, ECO Branch, FAA, has the authorityto approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in Related Information. You may email your request to: ANE-AD-AMOC@faa.gov. \n\t(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. \n\n(j) Related Information \n\n\n\tFor more information about this AD, contact Stephen Elwin, Aviation Safety Engineer, ECO Branch, FAA, 1200 District Avenue, Burlington, MA 01803; phone: (781) 238-7236; fax: (781) 238-7199; email: Stephen.L.Elwin@faa.gov. \n\n(k) Material Incorporated by Reference \n\n\n\t(1) The Director of the Federal Register approved theincorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. \n\t(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise. \n\t(i) General Electric Company (GE) GE90-100 Service Bulletin 73- 0118, Revision 01, dated April 27, 2021. \n\t(ii) (Reserved) \n\t(3) For GE service information identified in this AD, contact General Electric Company, 1 Neumann Way, Cincinnati, OH 45215; phone: (513) 552-3272; email: aviation.fleetsupport@ae.ge.com; website: www.ge.com. \n\t(4) You may view this service information at FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (781) 238-7759. \n\t(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email: fedreg.legal@nara.gov, or go to: https://www.archives.gov/federal-register/cfr/ibr-locations.html. \n\n\n\tIssued on July 9, 2021. Gaetano A. Sciortino, Deputy Director for Strategic Initiatives, Compliance & Airworthiness Division, Aircraft Certification Service. (FR Doc. 2021-16766 Filed 8-6-21; 8:45 am) BILLING CODE 4910-13-P

Supplementary Information

Background \n\n\n\tThe FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to all GE GE90-110B1 and GE90-115B model turbofan engines. The NPRM published in the Federal Register on May 7, 2021 (86 FR 24554). The NPRM was prompted by an in- service occurrence of loss of engine thrust control resulting in uncommanded high thrust. The FAA received a report from the manufacturer of an in-service loss of engine thrust control that occurred on October 27, 2019, resulting in uncommanded high thrust. Analysis by the manufacturer found accumulated thermal cycles of the MN4 integrated circuit in the FADEC, through normal operation, causes the solder ball joints to wear out and eventually fail over time. The FAA published AD 2020-20-17 (85 FR 63443, dated October 8, 2020) to prohibit dispatch of an airplane if certain status messages are displayed on the engine indicating and crew alerting system and if certain conditions are present per the manufacturer's service information. As a terminating action, AD 2020-20-17 also requires revision of the existing FAA-approved minimum equipment list (MEL) by incorporating into the MEL the dispatch restrictions listed in AD 2020- 20-17. Since the effective date of AD 2020-20-17, the manufacturer published GE GE90-100 Service Bulletin (SB) 73-0118 R00, dated November 6, 2020, and Revision 01, dated April 27, 2021, to replace the FADEC MN4 microprocessor and solder. In the NPRM, the FAA proposed to require initial and repetitive replacement of the FADEC MN4 microprocessor using an approved overhaul procedure. The FAA is issuing this AD to address the unsafe condition on these products. \n\nDiscussion of Final Airworthiness Directive \n\nComments \n\n\n\tThe FAA received comments from five commenters. Commenters included Air Line Pilots Association, International (ALPA), Boeing Commercial Airplanes (Boeing), Cathay Pacific Airways Limited (Cathay), FedEx Express (FedEx), and United Airlines, Inc. The following presents the comments received on the NPRM and the FAA's response to each comment. \n\nRequest To Revise Installation Prohibition \n\n\n\tCathay requested the FAA revise paragraph (h), Installation Prohibition, of the NPRM that specifies no more than three replacements of the FADEC MN4 microprocessor may be performed on the same main channel board. Cathay suggested that the FAA revise proposed paragraph (h) to prohibit installation onto any engine of any FADEC that is not compliant with GE GE90-100 SB 73-0118. Cathay stated that the MN4 processor replacements are managed by the original equipment manufacturer's (OEM) internal maintenance procedures and operators do not have visibility into the number of replacements that have been performed. \n\tThe FAA partially agrees. As stated by Cathay, the MN4 processor replacements are managed by the OEM's internal maintenance procedures and, therefore, are not necessary in this AD. The FAA has removed paragraph (h), Installation Prohibition, from this AD. The subsequent paragraphs of this AD have been redesignated accordingly. \n\nRequest To Add Terminating Action \n\n\n\tFedEx requested the upcoming FADEC software revision (A085) be included in this AD as a terminating action. FedEx commented that this AD may no longer be necessary due to the development and pending release of GE's new and improved FADEC software upgrade (A085). \n\tThe FAA disagrees. The new FADEC software revision (A085) has not been approved by the FAA. Therefore, this software is not eligible for installation and cannot be referenced in this AD. The FAA considers this AD to be an interim action. If terminating action is identified later, the FAA might consider additional rulemaking. The FAA did not change this AD. \n\n((Page 43410)) \n\nSupport for the AD \n\n\n\tALPA and Boeing expressed support for the NPRM as written. United Airlines, Inc. stated they had no objections to the NPRM as proposed. \n\nConclusion \n\n\n\tThe FAA reviewed the relevant data, considered any comments received, and determined that air safety requires adopting this AD as proposed. Accordingly, the FAA is issuing this AD to address the unsafe condition on these products. Except for minor editorial changes, and any other changes described previously, this AD is adopted as proposed in the NPRM. None of the changes will increase the economic burden on any operator. \n\nRelated Service Information Under 1 CFR Part 51 \n\n\n\tThe FAA reviewed General Electric GE90-100 Service Bulletin (SB) 73-0118, Revision 01, dated April 27, 2021. This SB specifies procedures for replacing the FADEC MN4 microprocessor. This service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in ADDRESSES. \n\nInterim Action \n\n\n\tThe FAA considers this AD to be an interim action. If final action is later identified, the FAA may consider additional rulemaking. \n\nCosts of Compliance \n\n\n\tThe FAA estimates that this AD affects 311 engines installed on airplanes of U.S. registry. \n\tThe FAA estimates the following costs to comply with this AD: \n\n\n\tEstimated Costs ---------------------------------------------------------------------------------------------------------------- \n\tCost per Cost on U.S. \n\tAction Labor cost Parts cost product operators ---------------------------------------------------------------------------------------------------------------- Remove and replace FADEC.............. 1 work-hour x $85 per $25,200 $25,285 $7,863,635 \n\thour = $85. ---------------------------------------------------------------------------------------------------------------- \n\n\n\tThe FAA has included all known costs in its cost estimate. According to the manufacturer, however, some of the costs of this AD may be covered under warranty, thereby reducing the cost impact on affected individuals. \n\nAuthority for This Rulemaking \n\n\n\tTitle 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. \n\tThe FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. \n\nRegulatory Findings \n\n\n\tThis AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. \n\tFor the reasons discussed above, I certify that this AD: \n\t(1) Is not a ''significant regulatory action'' under Executive Order 12866, \n\t(2) Will not affect intrastate aviation in Alaska, and \n\t(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. \n\nList of Subjects in 14 CFR Part 39 \n\n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Addresses

The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of September 13, 2021. \n\nADDRESSES: For service information identified in this final rule, contact General Electric Company, 1 Neumann Way, Cincinnati, OH 45215; phone: (513) 552-3272; email: aviation.fleetsupport@ae.ge.com; website: www.ge.com. You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (781) 238-7759. It is also available at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-0347. \n\nExamining the AD Docket \n\n\n\tYou may examine the AD docket at https://www.regulations.gov by searching for and locating Docket No. FAA-2021-0347; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M- 30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590.

For Further Information Contact

Stephen Elwin, Aviation Safety Engineer, ECO Branch, FAA, 1200 District Avenue, Burlington, MA 01803; phone: (781) 238-7236; fax: (781) 238-7199; email: Stephen.L.Elwin@faa.gov.