A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to all Boeing Model 737-100 and -200 series airplanes was published in the Federal Register on February 15, 2001 (66 FR 10390). That action proposed to require repetitive inspections to find fatigue cracking in the main deck floor beams located at certain body stations, and repair, if necessary. That action also proposed to provide for optional terminating action for the repetitive inspections. \n\nComments \n\n\tInterested persons have been afforded an opportunity to participate in the making of this amendment. Due consideration has been given to the comments received. \n\nExtend Compliance Time \n\n\tOne commenter asks that the compliance time for the detailed visual inspection specified in paragraph (a) of the proposal be extended. The commenter states that the service bulletin specified in the proposed rule is listedin Boeing Document D6-38505, which is titled "The Aging Airplane Service Bulletin Structural Modification and Inspection Program," hereinafter referred to as the "Boeing Document." The commenter notes that previous ADs issued against bulletins included in this document contain provisions to minimize the impact of the ADs. To be consistent with previous ADs, the commenter suggests that a 15-month phase-in period be implemented before the issuance of this proposed rule. \n\n\tThe FAA concurs. This final rule relates to the recommendations of the Airworthiness Assurance Task Force assigned to review Model 737 series airplanes, which indicate that, to assure long term continued operational safety, various structural inspections should be accomplished per the Boeing Document. To be consistent with the other inspections required by the Aging Airplane Program, we have extended the compliance time in paragraph (a) of this AD to within 6,000 flight cycles or 15 months after the effective dateof this AD, whichever occurs later. \n\n\tThe same commenter asks that the initial inspection specified in paragraph (a) of the proposed rule be done within 10,000 flight cycles after the effective date of the AD, instead of within 6,000 flight cycles. The commenter states that, due to the fact that the proposed rule requires a repetitive inspection interval that must be accomplished at a 'C' check interval, and the inspection area is not readily available, most operators will do the terminating action instead of the repetitive inspections. The commenter suggests that an initial 10,000-flight-cycle threshold be added to the rule that would allow operators to modify the floor structure without the 'C' check inspections. The commenter adds that it is doing the proposed inspections at a 4-year interval, and this interval is adequate to find and address cracks before they reach critical length. Additionally, at no time has the commenter found a crack that caused any risk of failure of the main deck floor beam. The commenter notes that the evident level of urgency of the proposed rule is unwarranted and adds that the referenced service bulletin has been a topic of the 737 Structures Task Group since 1993 with no significant findings presented to the industry to support an urgent, accelerated inspection program. \n\n\tThe FAA does not concur. Insufficient data were submitted to support the commenter's request. We are unable to validate that the level of urgency for the unsafe condition as specified in the service bulletin is unwarranted, because the data submitted does not include all the airplanes affected by this final rule. Additionally, the necessity for the inspection was established by a review conducted by the 737 Structures Working Group. As the commenter shows no correlation between a 4-year interval or 10,000 flight cycles, we have determined that no change to the final rule is necessary in this regard. \n\n\tA second commenter, the manufacturer, asks that the repetitive inspection interval specified in paragraph (a)(2)(i) of the proposal be changed from every 3,000 flight cycles to every 6,000 flight cycles. The commenter states that the repetitive inspection interval specified in the referenced service bulletin was changed following an investigation by the manufacturer that showed that inspecting every 6,000 flight cycles adequately addresses the unsafe condition. \n\n\tThe FAA concurs. The commenter provided documentation from the 737 Structures Working Group that supports an extension of the repetitive inspection interval. Paragraph (a)(2)(i) of the final rule has been changed accordingly. \n\nClarify Terminating Action \n\n\tOne commenter asks for clarification that repairs done per the referenced service bulletin terminate the repetitive inspections. The FAA concurs as this clarification is consistent with the referenced service bulletin. Paragraph (c) of the final rule has been revised accordingly. \n\nClarify Applicability \n\n\tOne commenter, the manufacturer, asks that the Applicability section of the proposed rule be changed to, "All Model 737-100 and "200 series passenger airplanes."\n\n\tThe FAA partially concurs. Model 737-200C series airplanes have a different structure in the areas specified in the proposed rule, and are not subject to the inspection requirements; however, 737-200C airplanes are not listed in the applicability of the proposed rule. The requested change is consistent with the effectivity specified in the referenced service bulletin; however, identifying the airplanes as "passenger" is not sufficient. Some passenger airplanes have been converted to freighters per a supplemental type certificate, and are still subject to the unsafe condition. The Summary section of the final rule has been changed to "certain" Model 737-100 and -200 series airplanes, and the Applicability section has been changed to add, "as listed in the referenced service bulletin," for clarification. \n\nRevise Preamble LanguageOne commenter asks that the Summary and Discussion sections of the proposed rule be changed to include information addressing the recommendations of the Airworthiness Assurance Task Force as published in the Boeing Document. The commenter states that, in AD 2000-07-12, amendment 39-11666 (65 FR 19310, May 16, 2000), the Discussion section gave significant detail explaining the purpose of the Aging Airplane Programs and why an AD was written against the service bulletin. The commenter adds that both sections should refer to the Boeing Document to reinforce the link between the proposal and the Aging Airplane Programs. \n\n\tWhile the FAA concurs with these comments in principle and acknowledges that the description of the Aging Airplane Programs could have been more specific in the Summary and Discussion sections, the Discussion section is not restated in this final rule. The intent of the Summary section of the final rule is to provide a brief explanation of the unsafe condition andthe action necessary to prevent failure of the main deck floor beams at certain body stations due to fatigue cracking. However, we have included information addressing the recommendations of the Airworthiness Assurance Task Force in the Summary section of the final rule. \n\nAllow Previously Approved Repairs \n\n\tOne commenter asks that previously installed approved repairs exceeding the service bulletin repair size terminate the inspections specified in paragraph (a) of the proposed rule. The commenter states that many operators have already done the inspections and repairs per the Boeing Document instead of the referenced service bulletin. The commenter adds that the proposed AD requires that all repairs not installed per the service bulletin be submitted to the FAA for approval. To ease the burden of approving previously installed repairs, the commenter suggests that paragraph (b) of the proposal should be changed to add, "* * * previously installed approved repairs exceeding the service bulletin repair size are considered terminating action for the inspections."\n\n\tThe FAA partially concurs. Previously approved repairs have been subject to analysis prior to acceptance as terminating action. Such repairs can be, in addition to the repairs described in the service bulletin, considered satisfactory and eliminate the need for reinspection in that area. The repairs do not have to be larger than the repairs described in the service bulletin to meet these conditions. However, installation of a local repair would eliminate the need for reinspection in the repaired area only. Paragraph (d) of this AD has been changed to add that the previously approved alternative methods of compliance (AMOC) of such repairs, issued for AD 90-06-02, amendment 39-6489 (55 FR 8372, March 7, 1990), and AD 93-08-04, amendment 39-8551 (58 FR 25546, April 27, 1993), are approved for this final rule. \n\nRevised Service Bulletin/Withdraw Proposed Rule \n\n\tThree commenters ask that a revised service bulletin be used for doing the actions specified in the proposed rule. One commenter asks that Boeing Service Bulletin 737-57-1210, Revision 1, be referenced in the proposed rule as the appropriate source of service information for doing of the specified actions, instead of the original issue that is now referenced. A second commenter states that it has done the modification specified in the proposed rule on approximately half of its fleet and at least eight of its airplanes have factory production changes which should negate the requirement to install modifications. The commenter adds that these changes are not identified in the service bulletin and notes that issuing an AD would be premature until the service bulletin can be revised. A third commenter asks that the proposed rule be put on hold until the manufacturer has updated the referenced service bulletin to include repairs to address the new conditions. \n\n\tThe FAA does not concur with the commenters. The AD will not berevised to reference Revision 1 of the service bulletin because we cannot approve the use of a document that does not yet exist. Due to the urgency of the unsafe condition, the final rule will be issued using the original issue of the service bulletin as the appropriate source of service information for doing the specified actions. However, operators may submit a request for an AMOC to use a later service bulletin through an appropriate FAA Principal Maintenance Inspector, as provided for by paragraph (d)(1) of this AD. \n\nCost Impact \n\n\tOne commenter states that the cost and time impacts for the inspection are unrealistic. The commenter notes that, although the FAA does not consider time necessary to gain access and return the area to the previous condition, this would constitute the majority of the time required to accomplish the inspections. The commenter adds that repetitive inspections would be required every 3,000 flight cycles, which would necessitate accomplishing the inspections on a special schedule when access to the area is not normally available. The commenter estimates that it would take 16 hours to gain access and close up, so the time and cost estimate for the inspection should be greatly increased. Also, if the cost data utilized by the FAA for procurement of parts is based upon the referenced service bulletin, then the data is approximately 10 years old and should be reviewed for accuracy. \n\n\tThe FAA does not concur with what it infers is a request to revise the cost estimate. We stated in the Cost Impact section of the proposed rule that, "The cost impact figures discussed in AD rulemaking actions represent only the time necessary to perform the specific actions actually required by the AD. These figures typically do not include incidental costs, such as the time required to gain access and close up, planning time, or time necessitated by other administrative actions." Our position on this matter has not changed since issuance of the proposed rule. No change to the final rule is necessary in this regard. \n\nConclusion \n\n\tAfter careful review of the available data, including the comments noted above, the FAA has determined that air safety and the public interest require the adoption of the rule with the changes previously described. The FAA has determined that these changes will neither increase the economic burden on any operator nor increase the scope of the AD. \n\nCost Impact \n\n\tThere are approximately 935 airplanes of the affected design in the worldwide fleet. The FAA estimates that 340 airplanes of U.S. registry will be affected by this AD, that it will take approximately 8 work hours per airplane to do the required inspection, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of the AD on U.S. operators is estimated to be $163,200, or $480 per airplane. \n\n\tThe cost impact figure discussed above is based on assumptions that no operator has yet done any of the proposed requirements of this AD action, and that no operator would do those actions in the future if this proposed AD were not adopted. The cost impact figures discussed in AD rulemaking actions represent only the time necessary to do the specific actions actually required by the AD. These figures typically do not include incidental costs, such as the time required to gain access and close up, planning time, or time necessitated by other administrative actions. \n\n\tShould an operator elect to do the optional terminating action rather than continue the repetitive inspections, it will take approximately 96 work hours per airplane to do the change, at an average labor rate of $60 per work hour. Required parts will cost between $218 and $1,426 per airplane. Based on these figures, the cost impact of this optional terminating action is estimated to be between $5,978 and $7,186 per airplane. \n\nRegulatory Impact \n\n\tThe regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132. \n\n\tFor the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption ADDRESSES. \n\nList of Subjects in 14 CFR Part 39 \n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. \n\nAdoption of the Amendment \n\n\tAccordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n\t1. The authority citation for part 39 continues to read as follows: \n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\nSec. 39.13 (Amended) \n\n\t2. Section 39.13 is amended by adding the following new airworthiness directive: