AD 2001-03-09

This amendment adopts a new airworthiness directive (AD), applicable to certain Boeing Model 777 series airplanes, that requires replacement of nuts on the clevis assemblies that support the auxiliary tracks of the inboard leading edge slats. This amendment is necessary to prevent loose or missing nuts on the clevis assemblies, which could cause the inboard leading edge slats to be loose or in an incorrect position and result in partial or total failure or loss of the slats. This action is intended to address the identified unsafe condition.

Final rule

2001-03-09 BOEING: Amendment 39-12113. Docket 2000-NM-285-AD. \n\n\tApplicability: Model 777 series airplanes, line numbers 1 through 155 inclusive, certificated in any category. \n\n\tNote 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (c) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it. \n\n\tCompliance: Required as indicated, unless accomplished previously.To prevent loose or missing nuts on the clevis assemblies that support the auxiliary tracks of the inboard leading edge slats, which could cause the slats to be loose or in an incorrect position and result in partial or total failure or loss of the slats, accomplish the following: \n\nReplacement \n\n\t(a) Within 18 months after the effective date of this AD, replace nuts having part number NAS1805-5L on the clevis assemblies that support the auxiliary tracks (outboard, center, and inboard) of the inboard leading edge slats with new nuts purchased from the airplane manufacturer after October 31, 1999, in accordance with Boeing Special Attention Service Bulletin 777-57-0038, dated February 24, 2000. \n\nSpares \n\n\t(b) As of the effective date of this AD, no person shall install any nut having part number NAS1805-5L on any airplane unless it was purchased from the airplane manufacturer after October 31, 1999. \n\nAlternative Methods of Compliance\n \n\t(c) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Seattle ACO. \n\n\tNote 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Seattle ACO. \n\nSpecial Flight Permits \n\n\t(d) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. \n\nIncorporation by Reference\n \n\t(e) The replacement shall be done in accordance with Boeing Special Attention Service Bulletin 777-57-0038, dated February 24, 2000. This incorporation by reference was approved by theDirector of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington 98124- 2207. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. \n\nEffective Date\n \n\t(f) This amendment becomes effective on March 23, 2001.

A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to certain Boeing Model 777 series airplanes was published in the Federal Register on November 15, 2000 (65 FR 68955). That action proposed to require replacement of nuts on the clevis assemblies that support the auxiliary tracks of the inboard leading edge slats. \n\nComments \nInterested persons have been afforded an opportunity to participate in the making of this amendment. Due consideration has been given to the comments received. \n\n\tOne commenter supports the proposed rule. Another commenter states that it is not affected by the proposed rule. \n\nConclusion \nAfter careful review of the available data, including the comments noted above, the FAA has determined that air safety and the public interest require the adoption of the rule as proposed. \n\nCost Impact \nThere are approximately 121 airplanes of the affected design in the worldwide fleet. The FAA estimates that 34 airplanes of U.S. registry will be affected by this AD, that it will take approximately 2 work hours per airplane to accomplish the required replacement, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of the AD on U.S. operators is estimated to be $4,080, or $120 per airplane. \n\n\tThe cost impact figure discussed above is based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted. The cost impact figures discussed in AD rulemaking actions represent only the time necessary to perform the specific actions actually required by the AD. These figures typically do not include incidental costs, such as the time required to gain access and close up, planning time, or time necessitated by other administrative actions. \n\nRegulatory ImpactThe regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132. \n\n\tFor the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption "ADDRESSES." \n\nListof Subjects in 14 CFR Part 39 \nAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. \n\nAdoption of the Amendment \nAccordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: \n\nPART 39 - AIRWORTHINESS DIRECTIVES \n1. The authority citation for part 39 continues to read as follows: \n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n§ 39.13 (Amended) \n2. Section 39.13 is amended by adding the following new airworthiness directive: