On February 13, 1991, the FAA issued AD 91-05-16, amendment 39-6913 (56 FR 7561, February 25, 1991), applicable to certain Boeing Model 737-100, -200, -300, -400, and -500 series airplanes. That AD requires repetitive visual and ultrasonic inspections of the main landing gear (MLG) actuator beam arms and actuator beam attach bolts for cracking, plating degradation, and corrosion; and rework or replacement, if necessary. The existing AD also provides for optional terminating action for the repetitive inspections. That action was prompted by reports of failure of the actuator beam arm and trunnion pin due to corrosion. The actions required by that AD are intended to prevent structural damage and severing of control cables and hydraulic tubing in this area, which could result in reduced controllability of the airplane. \n\nActions Since Issuance of Previous Rule\n \n\tSince the issuance of that AD, the FAA has received reports of cracking of an actuator beam arm on the MLG on three Boeing Model 737-300 series airplanes. Two operators reported damage to the landing gear, wing structure, fluid lines, and aileron and spoiler control cables; the damage has been attributed to fractures of the MLG actuator beam arm. One of those operators subsequently conducted a fleet-wide inspection and found a cracked actuator beam arm on another airplane. The beam arm fractures originated from corrosion pits in the actuator beam arm clevis. All three fractured actuator beam arms had been reworked in accordance with AD 91-05-16. In one case, the fracture occurred 7 years (at approximately 13,500 flight cycles) after completion of the terminating action in compliance with that AD. \n\nFAA's Conclusions \n\n\tThe FAA has determined that rework or replacement of the actuator beam arm, which AD 91-05-16 provides as either optional corrective action or optional terminating action for the repetitive inspections, does not adequately prevent corrosion and subsequent cracking of the clevis area. Therefore, the FAA finds that, to ensure the continued safety of the fleet, it is necessary to require that repetitive inspections to detect cracks and corrosion in the actuator beam arm clevis must be performed on all affected airplanes, including those on which the rework or replacement has been accomplished. Paragraph B. of AD 91-05-16, which provided for optional terminating action for the repetitive inspections, has not been included in this AD. \n\n\tIn addition, AD 91-05-16 requires a one-time inspection of the actuator beam attach bolts. However, there have been no known reports of bolt fractures since the effective date of AD 91-05-16. Therefore, the FAA has determined that further inspection of those bolts is unnecessary, and the corresponding requirement of AD 91-05-16 (paragraph A.2.) has not been included in this AD. The inspection requirements of this AD are limited to the actuator beam arm clevis. \n\n\tFurthermore, the FAA finds it necessary to expand the applicability of this AD to include additional airplanes. The applicability of AD 91-05-16 currently excludes in-production Model 737 series airplanes. However, the design change for incorporation on in-production airplanes can produce the same result as that of the preventive modification (rework) specified by Boeing Alert Service Bulletin 737-32A1224, Revision 1, dated April 12, 1990-which has been shown to be ineffective in preventing the unsafe condition. (That alert service bulletin is referenced as the appropriate source of service information in AD 91-05-16 for accomplishment of the rework.) \n\n\tTherefore, the applicability of this AD includes all Model 737-100, -200, -300, -400, and -500 series airplanes. \n\nExplanation of Relevant Service Information \n\n\tThe FAA has reviewed and approved Boeing Service Bulletin 737-32A1224, Revision 2, dated April 25, 1991. The content of Revision 2 is similar to that of Revision 1, which was cited as the appropriate source of service information for accomplishment of the requirements of AD 91-05-16. Revision 2 was issued to clarify the actions and to revise the effectivity for various actions. \n\n\tThe FAA also has reviewed and approved Boeing Alert Service Bulletin 737-32A1314, dated April 15, 1999, which describes procedures for repetitive inspections of the clevis on certain actuator beam arm assemblies; the inspections include a visual inspection to detect corrosion and an ultrasonic inspection to detect cracking. The alert service bulletin also describes procedures for replacement of any beam arm having a cracked or corroded clevis with a new actuator beam arm. \n\n\tThe note in Figure 1 of Boeing Alert Service Bulletin 737-32A1314 references Temporary Revision (TR) 04-14 to the 737 Nondestructive Test (NDT) Manual. That note states that the TR would be issued prior to May 14, 1999; in fact, the manufacturer released that TR by telegraphic release on April 26, 1999. The TR contains newinformation that is needed to perform ultrasonic inspections for airplanes having certain actuator beam arm assemblies. Specifically, the TR provides instructions for procuring or fabricating NDT transducers that are needed to accomplish the inspections for those certain airplanes. \n\nExplanation of Requirements of Rule \n\n\tSince an unsafe condition has been identified that is likely to exist or develop on other airplanes of this same type design, this AD supersedes AD 91-05-16 to continue to require repetitive inspections to detect cracking of the actuator beam arm clevis of the MLG, and rework or replacement, if necessary. These actions are required to be accomplished in accordance with Boeing Alert Service Bulletin 737-32A1224, Revision 1, or Boeing Service Bulletin 737-32A1224, Revision 2. \n\n\tThis AD adds repetitive detailed visual inspections to detect corrosion and repetitive ultrasonic inspections to detect cracking of the actuator beam arm clevis; these actions terminatethe repetitive inspections described in Boeing Alert Service bulletin 737-32A1224, Revision 1, or Boeing Service Bulletin 737-32A1224, Revision 2. These inspections are required to be accomplished in accordance with Boeing Alert Service Bulletin 737-32A1314. \n\n\tFor airplanes on which any corrosion or cracking is found during any of the newly added inspections, this AD requires replacement of the actuator beam arm with a new actuator beam arm in accordance with Boeing Alert Service Bulletin 737-32A1314. \n\nDifference Between the Rule and the Relevant Service Information \n\n\tOperators should note that Alert Service Bulletin 737-32A1314 specifies compliance in terms of either years or flight cycles. However, the threshold and repetitive interval required by paragraph (b) of this AD are specified in terms of calendar time only; i.e., 4 years and 90 days, respectively. The unsafe condition identified by this AD is caused by corrosion, which is a function of time rather than accumulated flight cycles. \n\nInterim Action \n\n\tThis is considered to be interim action until final action is identified, at which time the FAA may consider further rulemaking. \n\nDetermination of Rule's Effective Date \n\n\tSince a situation exists that requires the immediate adoption of this regulation, it is found that notice and opportunity for prior public comment hereon are impracticable, and that good cause exists for making this amendment effective in less than 30 days. \n\nComments Invited \n\n\tAlthough this action is in the form of a final rule that involves requirements affecting flight safety and, thus, was not preceded by notice and an opportunity for public comment, comments are invited on this rule. Interested persons are invited to comment on this rule by submitting such written data, views, or arguments as they may desire. Communications shall identify the Rules Docket number and be submitted in triplicate to the address specified under the caption "ADDRESSES." All communications received on or before the closing date for comments will be considered, and this rule may be amended in light of the comments received. Factual information that supports the commenter's ideas and suggestions is extremely helpful in evaluating the effectiveness of the AD action and determining whether additional rulemaking action would be needed\n\n\tComments are specifically invited on the overall regulatory, economic, environmental, and energy aspects of the rule that might suggest a need to modify the rule. All comments submitted will be available, both before and after the closing date for comments, in the Rules Docket for examination by interested persons. A report that summarizes each FAA-public contact concerned with the substance of this AD will be filed in the Rules Docket. \n\n\tCommenters wishing the FAA to acknowledge receipt of their comments submitted in response to this rule must submit a self-addressed, stamped postcard on which the following statement is made:"Comments to Docket Number 99-NM-68-AD." The postcard will be date stamped and returned to the commenter. \n\nRegulatory Impact \n\n\tThe regulations adopted herein will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612, it is determined that this final rule does not have sufficient federalism implications to warrant the preparation of a Federalism Assessment. \n\n\tThe FAA has determined that this regulation is an emergency regulation that must be issued immediately to correct an unsafe condition in aircraft, and that it is not a "significant regulatory action" under Executive Order 12866. It has been determined further that this action involves an emergency regulation under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979). If it is determined thatthis emergency regulation otherwise would be significant under DOT Regulatory Policies and Procedures, a final regulatory evaluation will be prepared and placed in the Rules Docket. A copy of it, if filed, may be obtained from the Rules Docket at the location provided under the caption "ADDRESSES." \n\nList of Subjects in 14 CFR Part 39 \n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. \n\nAdoption of the Amendment \n\n\tAccordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:\n\n PART 39 - AIRWORTHINESS DIRECTIVES \n\n\t1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 (Amended) \n\t2. Section 39.13 is amended by removing amendment 39-6913 (56 FR 7561, February 25, 1991), and by adding a new airworthiness directive (AD), amendment 39-11165, toread as follows: