AD 91-19-05

Active

Fire Extinguisher System Wiring

Key Information
91-19-05
Active
September 26, 1991
Not specified
91-NM-179-AD
39-8032
Applicability
["Aircraft"]
["Large Airplane"]
Textron Aviation Inc.
BAe.125 Series 800A BH.125 Series 400A BH.125 Series 600A DH.125 Series 1A DH.125 Series 1A-522 DH.125 Series 1A/R-522 DH.125 Series 1A/S-522 DH.125 Series 3A DH.125 Series 3A/R DH.125 Series 3A/RA DH.125 Series 400A HS.125 Series 1B HS.125 Series 1B-522 HS.125 Series 1B/R-522 HS.125 Series 1B/S-522 HS.125 Series 3B HS.125 Series 3B/R HS.125 Series 3B/RA HS.125 Series 3B/RB HS.125 Series 3B/RC HS.125 Series 400B HS.125 Series 400B/1 HS.125 Series 401B HS.125 Series 403A(C) HS.125 Series 403B HS.125 Series 600A HS.125 Series 600B HS.125 Series 600B/1 HS.125 Series 600B/2 HS.125 Series 600B/3 HS.125 Series 700A HS.125 Series 700B HS.125 Series F3B HS.125 Series F3B/RA HS.125 Series F400B HS.125 Series F403B HS.125 Series F600B
Regulatory Text

91-19-05 BRITISH AEROSPACE: Amendment 39-8032. Docket No. 91-NM-179-AD.

Applicability: Model BAe 125-800A, Model HS.125-700A, and Model DH/BH/HS 125 series airplanes retrofitted with Garrett engines which are pre-mod 253274A; certificated in any category.

Compliance: Required as indicated, unless previously accomplished.

To prevent the loss of fire extinguishment capability, accomplish the following:

(a) Within 30 days after the effective date of this AD, perform a visual inspection of the engine fire extinguisher system wiring to detect crossed wiring, improperly identified or unidentified wiring and wiring supports, missing wiring supports, and loose or improperly locked electrical connectors, in accordance with British Aerospace Service Bulletin 26-31, dated February 25, 1991.

(b) If any discrepancy is found during the inspection required by paragraph (a) of this AD, prior to further flight, correct it in accordance with the instructions in British Aerospace Service Bulletin 26-31, dated February 25, 1991.

(c) An alternative method of compliance or adjustment of the compliance time, which provides an acceptable level of safety, may be used when approved by the Manager, Standardization Branch, ANM-113, FAA, Transport Airplane Directorate.

NOTE: The request should be forwarded through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Standardization Branch, ANM-113.

(d) Special flight permits may be issued in accordance with FAR 21.197 and 21.199 to operate airplanes to a base in order to comply with the requirements of this AD.

(e) The inspection and correction requirements shall be done in accordance with British Aerospace Service Bulletin 26-31, dated February 25, 1991. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR Part 51. Copies may be obtained from British Aerospace, PLC, Librarian for Service Bulletins, P.O. Box 17414, Dulles International Airport, Washington, D.C. 20041-0414. Copies may be inspected at the FAA, Transport Airplane Directorate, Renton, Washington; or at the Office of the Federal Register, 1100 L Street N.W., Room 8401, Washington, D.C.

This amendment (39-8032, AD 91-19-05) becomes effective on September 26, 1991.

AD Assistant

Get AI-powered answers about this AD, check applicability, and find compliance steps.

Sign Up to Unlock
References
This information is not available.
--- - Part 39
FAA Documents