AD 98-26-12

This amendment adopts a new airworthiness directive (AD), applicable to certain Dornier Model 328-100 series airplanes, that requires a one-time inspection to verify correct installation of the lockplates of the roll spoiler actuators, and corrective actions, if necessary. This amendment is prompted by issuance of mandatory continuing airworthiness information by a foreign civil airworthiness authority. The actions specified by this AD are intended to prevent fatigue cracking of the fork flanges of the roll spoiler actuators due to incorrect installation of the lockplates, which could result in reduced structural integrity of the components of the roll spoiler actuators, and consequent reduced controllability of the airplane.

Final rule

98-26-12 DORNIER LUFTFAHRT GMBH: Amendment 39-10953. Docket 98-NM-290-AD.
Applicability: Model 328-100 series airplanes, serial numbers 3005 through 3095 inclusive; certificated in any category.

NOTE 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Compliance: Required as indicated, unless accomplished previously.

To prevent fatigue cracking of the fork flanges of the roll spoiler actuators due to incorrect installation of the lockplates, which could result in reduced structural integrity of the components of the roll spoiler actuators, and consequent reduced controllability of the airplane, accomplish the following:

(a) Within 300 flight hours after the effective date of this AD, perform a one-time visual inspection to verify correct installation of the lockplates of the roll spoiler actuators, in accordance with Dornier Service Bulletin SB-328-27-263, dated June 29, 1998.

(1) If all lockplates of the roll spoiler actuators are correctly installed, no further action is required by this AD.

(2) If any lockplate of any roll spoiler actuator is installed incorrectly, prior to further flight, perform either an eddy current or dye penetrant inspection to detect cracks of the area surrounding the fork flanges of the roll spoiler actuators, in accordance with theservice bulletin.

(i) If no crack is detected, no further action is required by this AD.

(ii) If any crack is detected, prior to further flight, replace the roll spoiler actuator with a new or serviceable roll spoiler actuator in accordance with the service bulletin.

(b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116.

NOTE 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116.

(c) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished.

(d) The inspection and replacement shall be done in accordance with Dornier Service Bulletin SB-328-27-263, dated June 29, 1998. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from FAIRCHILD DORNIER, DORNIER Luftfahrt GmbH, P.O. Box 1103, D-82230 Wessling, Germany. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC.

NOTE 3: The subject of this AD is addressed in German airworthiness directive 1998-358, dated September 10, 1998.

(e) This amendment becomes effective on January 25, 1999.

A proposal to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) to include an airworthiness directive (AD) that is applicable to certain Dornier Model 328-100 series airplanes was published in the Federal Register on October 27, 1998 (63 FR 57258). That action proposed to require a one-time inspection to verify correct installation of the lockplates of the roll spoiler actuators, and corrective actions, if necessary.

Comments
Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were submitted in response to the proposal or the FAA's determination of the cost to the public.

Conclusion
The FAA has determined that air safety and the public interest require the adoption of the rule as proposed.

Cost Impact
The FAA estimates that 50 airplanes of U.S. registry will be affected by this AD, that it will take approximately 1 work hour per airplane to accomplish the requiredinspection, and that the average labor rate is $60 per work hour. Based on these figures, the cost impact of the AD on U.S. operators is estimated to be $3,000, or $60 per airplane.

The cost impact figure discussed above is based on assumptions that no operator has yet accomplished any of the requirements of this AD action, and that no operator would accomplish those actions in the future if this AD were not adopted.

Regulatory Impact
The regulations adopted herein will not have substantial direct effects on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, in accordance with Executive Order 12612, it is determined that this final rule does not have sufficient federalism implications to warrant the preparation of a Federalism Assessment.

For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption "ADDRESSES."

List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39 - AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.

39.13 [Amended]
2. Section 39.13 is amended by adding the following new airworthiness directive: