78-25-02\tGATES LEARJET: Amendment 39-3362. Applies to those Model 35 (Serial Numbers 35-001 through 35-167) and 36 (Serial Numbers 36-001 through 36-038) airplanes, certificated in all categories, which have a 36-inch wide (as opposed to 24-inch wide) cabin door. \n\n\tCompliance: Required as indicated in accordance with Compliance Table I set forth in this AD, unless already accomplished. \n\n\tTo assure proper locking of the cabin upper door when the inside handle is in the locked position and to prevent possible unwanted door openings that may occur, accomplish the following at the time intervals noted in Table I of this AD: \n\n\n\n\n\n\nTABLE I COMPLIANCE TIMES \nAD 78-25-02 \n\nINSPECTION TIMES\nAirplane\nTotal Time \nIn Service\n(Hours)\n\nParagraph "A" Bolt \nInspection & Replacement\n\nParagraph "B" Locking \nMechanism Inspection\n\n Initial\n Inspection/\nReplacement\nInterval for\nRepetitive\nInspections/\nReplacement \nInitial\nInspection\nInterval for \nRepetitive \nInspections \n0 - 2,999 \nPrior to or \nupon the accumulation of 3,075 hours' time in service\nEach 3,000 hours' time in service there- after\nIn accordance with asterisk (*) paragraph below or upon accumulation of 6,075 hours' time in service, whichever occurs first\nIn accordance with asterisk (*) paragraph below or upon accumulation of each 6,000 hours' time in service after initial inspection\n3,000 - 5,999\nWithin 75\nhours' time in service after the effective date of this AD\nEach 3,000\nHours' time in service thereafter\nIn accordance with asterisk (*) paragraph below or upon accumulation of 6,075 hours' time in service, whichever occurs first\nIn accordance with asterisk (*) paragraph below or upon accumulation of each 6,000 hours' time in service after initial inspection\n6,000 - up\nWithin 75 hours' time in service after the effective date of this AD\nEach 3,000 hours' time in service there-after\nWithin 5 \nhours' time in service after the effective date of this AD\nIn accordance with asterisk (*) paragraph below or upon accumulation of each 6,000 hours; time in service after initial inspection\n* The door locking mechanism inspection must be accomplished any time the bolt inspection required by Paragraph "A" of this AD reveals a cracked, bent, broken or worn bolt. \n\n\tA)\tInspect and replace, at the time intervals noted in Table I above, the bolt identified as 5 in Figure I of this AD in accordance with Gates Learjet 35/36/35A/36A Maintenance Manual Temporary Revisions No. 5-52 and 5-55 or later revisions and as summarized below: \n\t\t1)\tRemove the bolt from the upper door rod control assembly and visually inspect it for cracks, breaks, bends, or wear. If any of the aforementioned defects are found, accomplish the door locking mechanism inspection required by Paragraph "B" of this AD prior to the next flight; and \n\t\t2)\tReplace the bolt removed in Paragraph A)1) of this AD with a new Gates Learjet Part Number 2311490-8 Bolt, or a new AN3-21 Bolt modified in accordance with Detail "A" in Figure I of this AD, and secure using an AN960D10 Washer and either a new MS20365- 1032 Nut or AN310-3 Nut and MS24665-132 Cotter Pin. \n\n\n\n\n\n\tB)\tInspect, at the time intervals noted in Table I above, the cabin door locking mechanism in accordance with Gates Learjet 35/36/35A/36A Maintenance Manual Temporary Revision No. 5-54 or later revisions, and as summarized below: \n\n\t\t1)\tDrill out rivets and remove cabin upper door inner panel. \n\n\t\t2)\tRemove and inspect door locking mechanism for wear and defects in accordance with Learjet Service Manual Inspection Requirements. The maximum allowable diameter (measured in any direction) of the hole in which the 5 bolt is installed is .201 inches. Replace any excessively worn or defective parts prior to the next flight. \n\n\t\t3)\tReinstall door locking mechanism and using rivets, reinstall the inner panel. \n\n\t\t4)\tCheck door locking mechanism for free movement with no binding thru entire operating travel. Correct any binding prior to the next flight. \n\n\t\t5)\tEnergize door warning system and check its operation for proper functioning. \n\n\tC)\tSubmit a written report on any cracked, broken, bent or worn 5 (See Figure I of this AD) bolts discovered during inspections required by this AD to the FAA via a letter to FAA, Chief, Engineering and Manufacturing Branch (ACE-210), 601 East 12th Street, Kansas City, Missouri 64106 or an FAA M or D report (FAA Form 8330-2). The report must include airplane model, serial number, airplane total time-in-service, bolt or pin total time-in-service and statements describing the condition of the bolt and the hole including dimensions of the hole determined in accordance with Paragraph B)2) of this AD. (Reporting approved by the Office of Management and Budget under OMB No. 04-R0174.) \n\n\tD)\tThe actions made mandatory by Paragraphs A, B and C of this AD are no longer required when Gates Learjet Door Modification Kit AMK78-2 is installed. \n\n\tE)\tAirplanes may be flown in accordance with FAR 21.197 to a base where this AD can be accomplished. \n\n\tF)\tAny equivalent method of compliance with this AD must be approved by the Chief, Engineering and Manufacturing Branch, FAA, Central Region. \n\n\tThis amendment becomes effective December 14, 1978.