87-04-24 BEECH AIRCRAFT CORPORATION: Amendment 39-5599. Applies to the following Beech airplanes certificated in any category. \n\n\nMODEL\nSERIAL NUMBERS S/N\nREFERENCE SERVICE \nINSTRUCTION NO.\n65-A90, B90,\nLJ-114 thru LJ-1139;\nBeechcraft Mandatory \nC90, C90A;\n\nService Instruction\nE90;\nLW-1 thru LW-347;\nNo. 2028, Rev. III,\nF90;\nLA-2 thru LA-236\nrevised February 1987\n200, B200;\nBB-2; BB-6 thru BB-1211; \nBB-1213 thru BB-1253; \nBB-1255 thru BB-1261; \nBB-1263 thru BB-1267;\n\n200C, B200C;\nBL-1 thru BL-112 and \nBL-124 thru BL-127;\n\n200CT, B200CT;\nBN-1 thru BN-4;\n\n200T, B200T\nBT-1 thru BT-31; \n\n300\nFA-1 thru FA-38 and \nFA-40 thru FA-50\n\n1900\nUA-1 thru UA-3\n\n1900C\nUB-1 thru UB-62\n\nH90 (T-44A)\nLL-1 thru LL-18,\nLL-20 thru LL-31,\nLL-33 thru LL-40,\nLL-42 thru LL-48, and \nLL-50 thru LL-61\nBeech T-44A Service\nInstructions No. \nT-44A-0058, Rev. 1 \nA200 (C-12A)\nBD-1 thru BD-30;\nBeech C-12 Service\nA200 (C-12C)\nBC-1 thru BC-75;\nInstructions No.A200CT (C-12D)\nBP-1, BP-22, BP-24 thru BP-39; \nBP-40 and BP-45;\nC-12-0103, Rev. 1\nA200CT (RC-12D)\nGR-1 thru GR-13;\n\nA200CT (RC-12G)\nFC-1 thru FC-3; \n\nA200CT (FWC-12D)\nBP-7 thru BP-11; \n\nA200C (UC-12B)\nBJ-1 thru BJ-66\n\nA200CT (C-12D)\nBP-46 thru BP-51;\nBeech C-12 Service\nA200CT (C-12F)\nBP-52 thru BP-63;\nInstructions No.\nB200C (C-12F)\nBL-73 thru BL-112 and\nBL-118 thru BL-123; \nC-12-0112\n65-A90-1 (U-21A)\nLM-1 thru LM-63,\nLM-65, LM-67 thru LLM-69, \nLM-71 thru LM-107, \nand LM-112 thru LM-124;\nBeech U-21 Service \nInstruction No.\nU-21-0002, Rev. 1\n65-A90-1 (JU-21A)\nLM-64, LM-66, LM-70;\n\n65-A90-1 (U-21G)\nLM-125 thru LM-141; \n\n5-A90-1 (RU-21A)\nLM-108 thru LM-111;\n\n6 65-A90-2 (RU-21B)\nLS-1 thru LS-3;\n\n65-A90-3 (RU-21C)\nLT-1 and LT-2;\n\n65-A90-4 (RU-21H)\nLU-1 thru LU-16 \n\n\n\tCompliance: Required as indicated after the effective date of this AD, unless previously accomplished. \n\n\tTo preclude malfunction of the elevator trim cable system, accomplish the following: \n\n\t(a)\tWithin the next 10 hours time-in-service, perform the following: \n\n\t\t(1)\tFor Models 65-A90, B90, C90, C90A airplanes (S/N LJ-114 thru LJ-1110), and Model E90 airplanes (S/N LW-1 thru LW-347), which have complied with AD 86-20- 03, paragraph (b), and for Models C90A airplanes (S/N LJ-1111 thru LJ-1139), which have a redesigned elevator trim cable system installed at the Beech factory without moisture protection; modify the elevator trim system in accordance with Part IV of Beechcraft Service Bulletin No. 2028, Rev. III, dated February 1987. \n\n\t\t(2)\tFor Models F90 airplanes (S/N LA-2 and LA-235); Models 200 and B200 airplanes (S/N BB-2, BB-6 thru BB-1211 and BB-1213 thru BB-1217); and for Models 200C and B200C airplanes (S/N BL-1 thru BL-112 and BL-124); and for Models 200CT and B200CT airplanes (S/N BN-1 thru BN-4); and for Models 200T and B200T airplanes (S/N BT-1 thru BT-30), which have complied with AD 86-20-03, paragraph (b), and for Models F90 airplane (S/N LA-236); and for Models 200 and B200 airplanes (S/N BB-1218 thru BB-1253, BB-1255 thru BB-1261, BB-1263 thru BB-1267); and for Models B200C airplanes (S/N BL-125 thru BL-127); and for Models B200T airplane (S/N BT-31), which have a redesigned elevator trim cable system installed at the Beech factory without moisture protection; modify the elevator trim system in accordance with Part V of Beechcraft Service Bulletin No. 2028, Rev. III, dated February 1987. \n\n\t\t(3)\tFor Models 1900 airplanes (S/N UA-1 thru UA-3) and for Models 1900C airplanes (S/N UB-1 thru UB-44), which have complied with AD 86-20-03, paragraph (b), and for Models 1900C airplanes (S/N UB-45 thru UB-62), which have a redesigned elevator trim cable system installed at the Beech factory without moisture protection; modify the elevator trim system in accordance with Part VI of Beechcraft Service Bulletin No. 2028, Rev. III, dated February 1987. \n\n\t(b)\tFor those airplanes that have not been modified in accordancewith paragraph (b) of AD 86-20-03, within the next 25 hours time-in-service, accomplish the following: \n\n\t\t(1)\tCheck the operation of the elevator trim system and mark the elevator trim indicator scale in accordance with Part I or Part II of Beech Service Bulletin No. 2028, Rev. III, dated February 1987. \n\n\t\t(2)\tFor Models 65-A90, B90, C90, C90A, and E90 airplanes, mark the elevator trim tab push rods in accordance with Part I or Part II of Beech Service Bulletin No. 2028, Rev. III, dated February 1987. \n\n\tNOTE: The following airplanes have been previously marked by the manufacturer per paragraphs (a)(1) and (a)(2) of AD 86-20-03: Models C90A (S/N LJ-1077 thru LJ-1110), F90 (S/N LA-223 thru LA-235), B200 (S/N BB-1193 thru BB-1217), B200C (S/N BL-72 thru BL-112 and BL-124), 300 (S/N FA-1 thru FA-38 and FA-40 thru FA-50), 1900 (S/N UA-1 thru UA-3), and 1900C (S/N UB-9 thru UB-44). \n\n\t\t(3)\tPlace the Elevator Trim System Preflight Check Procedure, shown in Attachment 1 of this AD, in the Limitations Section of the FAA Approved Flight Manual for the Models 65-A90, B90, C90, E90, and 200T/200CT airplanes; and the Limitations Section of the Pilot's Operating Handbook and the FAA Approved Airplane Flight Manual for the Models C90, C90A, F90, 200/200C, B200/B200C, B200T, B200CT, 300, and 1900/1900C airplanes. \n\n\t(c)\tPrior to May 15, 1987, modify the elevator trim system on all airplanes which have not complied with the requirements of paragraph (a) of this AD, in accordance with Part III of Beechcraft Service Bulletin No. 2028, Rev. III, dated February 1987. \n\n\t(d)\tCompliance with paragraph (b) of this AD is no longer necessary after the modification required in paragraph (c) of this AD is accomplished. \n\n\t(e)\tAirplanes may be flown in accordance with FAR 21.197 to a location where the AD may be accomplished. \n\n\t(f)\tAn equivalent means of compliance with this AD may be used, if approved by the Manager, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Mid- Continent Airport, Wichita, Kansas 67209; Telephone (316) 946-4400. \n\n\tAll persons affected by this directive may obtain copies of the document(s) referred to herein upon request to Beechcraft Aero and Aviation Centers or Beech Aircraft Corporation, Commercial Service Department 52, P.O. Box 85, Wichita, Kansas 67201-0085; or may examine copies of the document(s) referred to herein at the FAA, Office of the Regional Counsel, Room 1558, 601 East 12th Street, Kansas City, Missouri 64106. \n\n\tThis AD supersedes AD 86-20-03, Amendment 39-5413. \n\n\tThis amendment becomes effective on April 14, 1987, to all persons except those to whom it has already been made effective by priority letter from the FAA dated February 23, 1987, and is identified as AD 87-04-24. \n\nATTACHMENT 1 - 87-04-24 \n\nOPERATING LIMITATION: \n\n\tThe Elevator Trim System Preflight check procedure, as defined below, must be conducted prior to each flight. \n\n\tTo verify that the elevator trim cable is not fouled or disengaged from the cable drum, the following Elevator Trim System Preflight Check is required prior to each flight of the Beech Model 65-A90, B90, C90, C90A, E90, F90, 200, B200, 200C, B200C, 200CT, B200CT, 200T, B200T, 300, 1900 and 1900C airplanes: \n\nCOCKPIT \n\n\t1.\tControl Locks - REMOVE \n\n\t2.\tElevator Trim: \n\n\t\ta.\tAll airplanes except 1900/1900C - SET TO "O" UNITS \n\n\t\tb.\t1900/1900C airplanes - SET TWO UNITS NOSE UP CAUTION \n\n\t\t\tThe elevator trim system must not be forced past the limits which are indicated on the elevator trim indicator scale either manually, electrically (except Model 300) or by action of the autopilot (except Model 300). \n\nTAIL SECTION \n\n\t1.\tElevator Trim Tab \n\n\t\ta.\tVERIFY "O" (NEUTRAL) POSITION \n\n\t2.\tOn Model 65-A90, B90, C90, C90A and E90 airplanes, the elevator trim tab "O" (neutral) position is determined by observing that the alignment marks on the elevator trim tab pushrods align with the alignment marks on the elevator (See Figure 1 or 2 below), when the elevator is resting against the downstops. \n\n\t3.\tOn Model F90, 200 Series, 300 and 1900/1900C airplanes, the elevator trim tab "O" (neutral) position is determined by observing that the trailing edge of the elevator trim tab aligns with the trailing edge of the elevator, when the elevator, when the elevator is resting against the downstops.\n\n WARNING \n\n\tThe above Preflight Inspection check MUST be repeated prior to take-off if the elevator trim is allowed to reach limit travel at any time prior to take-off as a result of MANUAL, ELECTRICAL (except Model 300) OR AUTOPILOT (except Model 300) OPERATION of the trim system.