Discussion \n\n\n\tThis AD is prompted by the results of an investigation of a March 11, 2018, fatal accident in which an Airbus Helicopters Model AS350B2 helicopter impacted a body of water during an autorotation. The left- hand and right-hand emergency floats did not inflate symmetrically and the helicopter subsequently capsized. \n\tDuring the accident investigation, the FAA learned of reports of difficulty pulling the emergency float kit float activation handle installed on the pilot cyclic. Asymmetric inflation of the float system and difficulty deploying the float system from the float activation handle installed on the pilot cyclic can be caused by improperly installed pull cables. These emergency float kits utilize a system of pull cables to activate and release compressed gas from the float cylinders into the floats. Proper installation of the pull cables allows the two float cylinders installed on the aircraft to activate simultaneously, allowingfor proper distribution of gas to all floats in the system. Improperly installed pull cables, if not addressed, could result in loss of the left- or right-hand float, causing the helicopter to roll to one side but remain buoyant, or loss of both floats, causing the helicopter to capsize underwater. \n\tThese emergency float systems are installed on Airbus Helicopters Model AS350B, AS350BA, AS350B1, AS350B2, AS350B3, AS350C, AS350D, and AS350D1 helicopters under Supplemental Type Certificate (STC) SR00470LA, and on Model AS355E, AS355F, AS355F1, AS355F2, AS355N, and AS355NP helicopters under STC SR00645LA. Both STCs are held by Apical Industries, Inc., d/b/a DART Aerospace (DART). Following the investigation, DART developed a test tool to verify correct installation and rigging of the pull cables and subsequently issued service information to provide instructions for using the test tool. The FAA approved these instructions to correct the unsafe condition on November 13, 2019. Accordingly, the FAA is issuing this AD to address the unsafe condition on these products. \n\n((Page 8151)) \n\nRelated Service Information Under 1 CFR Part 51 \n\n\n\tThe FAA has reviewed DART Aerospace Service Bulletin SB-2018-07, Revision D, dated November 25, 2019. This service information contains procedures for inspecting the installation of the pull cables on 20326- series part-numbered emergency float kits (e.g., inspecting for activation pull forces on the float activation handle), readjusting the cable rigging if improperly installed, and contacting DART if readjusting the rigging is not successful. This service information also contains optional procedures for deactivating the emergency float system as inoperative. \n\tThis service information is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. \n\nOther Related Service Information \n\n\n\tThe FAA has also reviewed DART Aerospace Service Bulletin SB-2018- 07, Revision B, dated October 8, 2019, and DART Aerospace Service Bulletin SB-2018-07, Revision C, dated November 14, 2019. The actions specified in these service bulletins are the same as those specified in DART Aerospace Service Bulletin SB-2018-07, Revision D, dated November 25, 2019. DART Aerospace Service Bulletin SB-2018-07, Revision C, dated November 14, 2019, adds a note that includes a reference to the instructions for continued airworthiness for a specific float system configuration that was not in DART Aerospace Service Bulletin SB-2018- 07, Revision B, dated October 8, 2019. DART Aerospace Service Bulletin SB-2018-07, Revision D, dated November 25, 2019, clarifies certain references to the operational instructions manual. These differences do not affect how operators would accomplish the actions necessary to address the identified unsafe condition. \n\nFAA's Determination \n\n\n\tThe FAA is issuing this AD after evaluating all the relevant information and determining the unsafe condition described previously is likely to exist or develop in other products of the same type design. \n\nAD Requirements \n\n\n\tThis AD requires repetitive inspections of the installation of the pull cables on the emergency float kits and corrective action if necessary. \n\nDifferences Between This AD and the Service Information \n\n\n\tDART Aerospace Service Bulletin SB-2018-07, Revision D, dated November 25, 2019, specifies accomplishing the actions before March 31, 2020, while this AD requires compliance within 100 hours time-in- service (TIS) or 30 days after the effective date of this AD, whichever occurs first. \n\nFAA's Justification and Determination of the Effective Date \n\n\n\tSection 553(b)(3)(B) of the Administrative Procedure Act (5 U.S.C.) authorizes agencies to dispense with notice and comment procedures for rules when the agency, for ''good cause'' finds that those procedures are ''impracticable, unnecessary, or contrary to the public interest.'' Under this section, an agency, upon finding good cause, may issue a final rule without seeking comment prior to the rulemaking. \n\tAn unsafe condition exists that requires the immediate adoption of this AD without providing an opportunity for public comments prior to adoption. The FAA has found that the risk to the flying public justifies waiving notice and comment prior to adoption of this rule because improperly installed pull cables may lead to asymmetric inflation of the float system or difficulty deploying the float system from the float activation handle installed on the pilot cyclic, which could result in the loss of one or more floats. Loss of the left- or right-hand float could cause the helicopter to roll to one side but remain buoyant, while loss of both floats could cause the helicopter to capsize underwater. Because of the high utilization rate of helicopters with these emergency float kits installed, and because these helicopters primarily conduct operationsover water, the FAA determined a compliance time of no more than 100 hours TIS or 30 days, whichever occurs first, was required to correct the unsafe condition. This compliance time is shorter than the time necessary for the public to comment and for publication of the final rule. Therefore, notice and opportunity for prior public comment are impracticable and contrary to public interest pursuant to 5 U.S.C. 553(b)(3)(B). In addition, for the reasons stated above, the FAA finds that good cause exists pursuant to 5 U.S.C. 553(d) for making this amendment effective in less than 30 days. \n\nComments Invited \n\n\n\tThis AD is a final rule that involves requirements affecting flight safety and was not preceded by notice and an opportunity for public comment. However, the FAA invites you to send any written data, views, or arguments about this final rule. Send your comments to an address listed under the ADDRESSES section. Include the docket number FAA-2020- 0125 and Product Identifier 2019-SW-104-AD at the beginning of your comments. The FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of this final rule. The FAA will consider all comments received by the closing date and may amend this final rule because of those comments. \n\tThe FAA will post all comments received, without change, to https://www.regulations.gov, including any personal information you provide. The FAA will also post a report summarizing each substantive verbal contact received about this final rule. \n\nRegulatory Flexibility Act \n\n\n\tThe requirements of the Regulatory Flexibility Act (RFA) do not apply when an agency finds good cause pursuant to 5 U.S.C. 553 to adopt a rule without prior notice and comment. Because FAA has determined that it has good cause to adopt this rule without notice and comment, RFA analysis is not required. \n\nCosts of Compliance \n\n\n\tThe FAA estimates that this AD affects 71 helicopters of U.S. registry. The FAA estimates the following costs to comply with this AD: \n\n\n\tEstimated Costs ---------------------------------------------------------------------------------------------------------------- \n\tCost per Cost on U.S. \n\tAction Labor cost Parts cost helicopter operators ---------------------------------------------------------------------------------------------------------------- Inspection......................... 3 work-hours x $85 per hour $0 $255 $18,105 \n\t= $255 per inspection. ---------------------------------------------------------------------------------------------------------------- \n\n\n\n((Page 8152)) \n\n\n\tThe inspection requires the use of a pull cable test kit, which costs $2,000. Only one pull cable test kit is needed per operator such that the operator may use the same pull cable test kit on any affected helicopter. The FAA has no way of determining what on-condition actions may be required following the inspection required by this AD, the number of helicopters that might need on-condition actions, or the costs to perform the on-condition actions. \n\tAccording to the manufacturer, some or all of the costs of this AD may be covered under warranty, thereby reducing the cost impact on affected individuals. The FAA does not control warranty coverage for affected individuals. As a result, the FAA has included all known costs in the cost estimate. \n\nAuthority for This Rulemaking \n\n\n\tTitle 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs describes in more detail the scope of the Agency's authority. \n\tThe FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. \n\nRegulatory Findings \n\n\n\tThis AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. \n\tFor the reasons discussed above, I certify that this AD: \n\t(1) Is not a ''significant regulatory action'' under Executive Order 12866, and \n\t(2) Will not affect intrastate aviation in Alaska. \n\nList of Subjects in 14 CFR Part 39 \n\n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.