Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0 1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0 2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):
2019-01-07 Airbus SAS: Amendment 39-19546; Docket No. FAA-2018-0705; Product Identifier 2018-NM-077-AD.
(a) Effective Date
This AD is effective March 19, 2019.
(b) Affected ADs
None.
(c) Applicability
This AD applies to Airbus SAS Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes, certificated in any category, as identified in Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018.
(d) Subject
Air Transport Association (ATA) of America Code 57, Wings.
(e) Reason
This AD was prompted by a report that during removal of left- hand (LH) gear rib 5, four failed fasteners (bolts attaching the gear rib to the wing inner rear spar) were discovered. We are issuing this AD to address cracked or failed (broken) fasteners (bolts) of the rib 5-to-rear spar attachment, which could lead to reduced structural integrity of the wing.
(f) Compliance
Comply with this AD within the compliance times specified, unless already done.
(g) Inspection of the Rib 5-to-Rear Spar Attachment Fasteners (Bolts)
Within 30 months after the effective date of this AD, do a special detailed (ultrasonic) inspection of the LH and right-hand (RH) wing rib 5-to-rear spar attachment fasteners (bolts) for cracked or failed (broken) fasteners (bolts), in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018.
(h) Replacement of Cracked or Failed Fasteners (Bolts)
If any cracked or failed (broken) fastener (bolt) is found during any inspection required by paragraph (g) of this AD, before further flight, do the actions specified in paragraphs (h)(1), (h)(2), (h)(3), and (h)(4) of this AD, as applicable.
(1) Do a detailed inspection of the gear rib 5 and spar web for cracks and damage (cracks along the length of the bolt or broken bolt), in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018. If any crack or damage is found during any inspection required by this paragraph, before further flight, obtain corrective actions approved by the Manager, International Section, Transport Standards Branch, FAA; or the European Aviation Safety Agency (EASA); or Airbus SAS's EASA Design Organization Approval (DOA); and accomplish the corrective actions within the compliance time specified therein. If approved by the DOA, the approval must include the DOA-authorized signature.
(2) If no cracks or damage are found during any inspection required by paragraph (h)(1) of this AD: Do a rotating probe test of the gear rib and spar web bolt holes for cracks and damage (cracks in the bolt holes), in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018. If any crack or damage is found during any inspection required by this paragraph, before further flight, obtain corrective actions approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's EASA DOA; and accomplish the corrective actions within the compliance time specified therein. If approved by the DOA, the approval must include the DOA authorized signature.
(3) If no cracks or damage are found during any inspection required by paragraph (h)(2) of this AD: Ream the gear rib and the spar web bolt holes, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018. Ifan oversize larger than 0.794 millimeter (0.0313 inch) is required, before further flight, obtain corrective actions approved by the Manager, International Section, Transport Standards Branch, FAA; or EASA; or Airbus SAS's EASA DOA; and accomplish the corrective actions within the compliance time specified therein. If approved by the DOA, the approval must include the DOA authorized signature.
(4) Replace any cracked or failed fasteners (bolts) in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018.
(i) Reporting
Within 90 days after the special detailed inspection required by paragraph (g) of this AD, or within 30 days after the effective date of this AD, whichever occurs later, report the inspection results (both positive and negative) to Airbus SAS in accordance with the Accomplishment Instructions of Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018. If operators have reported findings as part of obtaining any corrective actions approved by the EASA DOA, operators are not required to report those findings as specified in this paragraph.
(j) Credit for Previous Actions
This paragraph provides credit for actions required by paragraphs (g), (h), and (i) of this AD, if those actions were performed before the effective date of this AD using Airbus Service Bulletin A320-57-1167, Revision 01, dated January 16, 2018.
(k) Paperwork Reduction Act Burden Statement
A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information
[[Page 3288]]
displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated tobe approximately 1 hour per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW, Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200.
(l) Other FAA AD Provisions
The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, International Section, Transport Standards Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the International Section, send it to the attention of the person identified in paragraph (m)(2) of this AD. Information may be emailed to: 9-ANM-116-AMOC-REQUESTS@faa.gov. Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.
(2) Contacting the Manufacturer: For any requirement in this AD to obtain corrective actions from a manufacturer, the action must be accomplished using a method approved by the Manager, International Section, Transport Standards Branch, FAA; or the EASA; or Airbus SAS's EASA DOA. If approved by the DOA, the approval must include the DOA-authorized signature.
(3) Required for Compliance (RC): Except as required by paragraph (i) of this AD, if any service information contains procedures or procedures and tests must be done to comply with this AD; any procedures or tests that are not identified as RC are recommended. Those procedures and tests that are not identified as RC may be deviated fromusing accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the procedures and tests identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to procedures or tests identified as RC require approval of an AMOC.
(m) Related Information
(1) Refer to Mandatory Continuing Airworthiness Information (MCAI) EASA AD 2018-0102, dated April 27, 2018, for related information. This MCAI may be found in the AD docket on the internet at http://www.regulations.gov by searching for and locating Docket No. FAA-2018-0705.
(2) For more information about this AD, contact Sanjay Ralhan, Aerospace Engineer, International Section, Transport Standards Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3223.
(3) Service information identified in this AD that is not incorporated by reference is available at the addresses specified in paragraphs (n)(3) and (n)(4) of this AD.
(n) Material Incorporated by Reference
(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise.
(i) Airbus Service Bulletin A320-57-1167, Revision 02, dated August 14, 2018.
(ii) [Reserved]
(3) For service information identified in this AD, contact Airbus SAS, Airworthiness Office--EIAS, Rond-Point Emile Dewoitine No: 2, 31700 Blagnac Cedex, France; phone: +33 5 61 93 36 96; fax: +33 5 61 93 44 51; email: account.airworth-eas@airbus.com; internet: http://www.airbus.com.
(4) You may view this service information at the FAA, Transport Standards Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195.
(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.;