Background EASA, which is the Technical Agent for the Member States of the European Union, has issued EASA AD 2021-0281, dated December 17, 2021 (EASA AD 2021-0281) (also referred to as the MCAI), to correct an unsafe condition for Airbus SAS Model A330-201, -202, -203, -223, -223F, -243, and -243F airplanes, Model A330-301, -302, -303, -321, -322, -323, -341, -342, -343, and -743L airplanes. Model A330-743L airplanes are not certificated by the FAA and are not included on the U.S. type certificate data sheet; this AD therefore does not include those airplanes in the applicability. The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to supersede AD 2020-22-03, Amendment 39-21299 (85 FR 66873, October 21, 2020) (AD 2020-22-03). AD 2020-22-03 applied to all Airbus SAS Model A330-200, -200 Freighter, and -300 series airplanes. The NPRM published in the Federal Register on June 16, 2022 (87 FR 36266). The NPRM was prompted by the development of new maintenance actions and software related to over-temperature failure conditions. The NPRM proposed to continue to require the actions specified in AD 2020-22-03, to require accomplishing the new maintenance tasks and corrective actions, and to mandate embodiment of the updated FWC software for certain airplanes, as specified in EASA AD 2021-0281. The NPRM also proposed to prohibit the installation of affected FWC software. The FAA is issuing this AD to address the possibility of a jammed engine bleed valve, which could lead to damage of the bleed manifold and the ducts downstream of the engine bleed system, exposure of the surrounding structure to heat stress, and possible reduced structural integrity of the airplane. See the MCAI for additional background information. Discussion of Final Airworthiness Directive Comment The FAA received a comment from the Air Line Pilots Association, International (ALPA) who supported the NPRM without change. Conclusion The FAA reviewed the relevant data, considered the comment received, and determined that air safety requires adopting this AD as proposed. Accordingly, the FAA is issuing this AD to address the unsafe condition on this product. Except for minor editorial changes, this AD is adopted as proposed in the NPRM. None of the changes will increase the economic burden on any operator. Related Service Information Under 1 CFR Part 51 EASA AD 2021-0281 specifies procedures for amending the applicable AFM to incorporate procedures to be applied if an engine bleed over-temperature occurs when the associated engine bleed valve is jammed open. EASA AD 2020-0281 also specifies that embodiment of updated FWC software standard T9 eliminates the need for the AFM amendment. EASA AD 2021-0281 also describes maintenance tasks for failures related to over-temperature conditions and corrective actions (repair). EASA AD 2021-0281 also specifies procedures for the embodiment of updated FWC software standard T9-3, and, for certain airplanes concurrent embodiment of system data acquisition concentrator (SDAC) software standard C13 or FWC software standard K3-2 and SDAC software standard C3-0A. Finally, EASA AD 2021-0281 prohibits the installation of affected FWC software (FWC software standard T9-2 or earlier). This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in the ADDRESSES section. Costs of Compliance The FAA estimates that this AD affects 115 airplanes of U.S. registry. The FAA estimates the following costs to comply with this AD: Estimated Costs for Required Actions Labor cost Parts cost Cost per product Cost on U.S. operators AFM Revision: 1 work-hour × $85 per hour = $85 $0 $85 $9,775. Software Update: 3 work-hours × 85 per hour = $255 0 $255 Up to $29,325. Maintenance Tasks: 7 work-hours × $85 per hour = $595 720 $595 $151,225. Concurrent Actions: Up to 4 work-hours × $85 per hour = Up to $340 0 Up to $340 Up to $39,100. Estimated Costs for Optional Actions Labor cost Parts cost Cost per product 2 work-hours × $85 per hour = $170 $0 $170 The FAA has received no definitive data that enables the agency to provide cost estimates for the on-condition actions specified in this AD. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority. The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings This AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a "significant regulatory action" under Executive Order 12866, (2) Will not affect intrastate aviation in Alaska, and (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. The Amendment Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39-AIRWORTHINESS DIRECTIVES 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. § 39.13 [Amended] 2. The FAA amends § 39.13 by: a. Removing Airworthiness Directive (AD) 2020-22-03, Amendment 39-21299 (85 FR 66873, October 21, 2020); and b. Adding the following new airworthiness directive: 2022-17-08 Airbus SAS: Amendment 39-22146; Docket No. FAA-2022-0680; Project Identifier MCAI-2021-01415-T. (a) Effective Date This airworthiness directive (AD) is effective October 13, 2022. (b) Affected ADs This AD replaces AD 2020-22-03, Amendment 39-21299 (85 FR 66873, October 21, 2020) (AD 2020-22-03). (c) Applicability This AD applies to all Airbus SAS Model airplanes, certificated in any category, as identified in paragraphs (c)(1) though (3) of this AD. (1) Model A330-201, -202, -203, -223, and -243 airplanes. (2) Model A330-223F and -243F airplanes. (3) Model A330-301, -302, -303, -321, -322, -323, -341, -342, and -343 airplanes. (d) Subject Air Transport Association (ATA) of America Code 75, Air; Code 36, Pnuematic. (e) Unsafe Condition This AD was prompted by a report that during a certification exercise, it was identified that there was a risk of an engine bleed system over-temperature, without the engine bleed valve closing; the associated engine bleed valve should automatically close. This AD was also prompted by the development of new maintenance actions and software related to over-temperature failure conditions. The FAA is issuing this AD to address the possibility of a jammed engine bleed valve, which could lead to damage of the bleed manifold and the ducts downstream of the engine bleed system, exposure of the surrounding structure to heat stress, and possible reduced structural integrity of the airplane. (f) Compliance Comply with this AD within the compliance times specified, unless already done. (g) Requirements Except as specified in paragraph (h) of this AD: Comply with all required actions and compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2021-0281, dated December 17, 2021 (EASA AD 2021-0281). (h) Exceptions to EASA AD 2021-0281 (1) Where EASA AD 2021-0281 refers to October 1, 2020 (the effective date of EASA AD 2020-0205), this AD requires using November 5, 2020 (the effective date of AD 2020-22-03). (2) Where EASA AD 2021-0281 refers to its effective date, this AD requires using the effective date of this AD. (3) Where paragraph (1) of EASA AD 2021-0281 specifies to "inform all flight crews, and, thereafter, operate the aeroplane accordingly," this AD does not require those actions as those actions are already required by existing FAA operating regulations. (4) Where paragraphs (6) and (7) of EASA AD 2021-0281 specifies actions if "any discrepancies are detected," for this AD discrepancies include failures related to an over-temperature situation, hidden failures in equipment for a "not isolated over-temperature" failure condition, cracking on the exchanger outlet temperature sensor, or dual drift in the exchanger outlet temperature sensor. (5) Where paragraph (11) of EASA AD 2021-0281 specifies that an airplane with certain modifications is compliant with "the requirements of paragraph (2) of EASA AD 2020-0077," for this AD use "for the corresponding requirements of paragraph (2) of EASA AD 2020-0077 that are required by paragraph (g) of AD 2020-17-16, Amendment 39-21221 (85 FR 54900, September 3, 2020)." (6) The "Remarks" section of EASA AD 2021-0281 does not apply to this AD. (i) No Reporting Requirements Although the service information referenced in EASA AD 2021-0281 specifies to submit certain information to the manufacturer, this AD does not include that requirement. (j) Additional FAA AD Provisions The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Large Aircraft Section, International Validation Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or responsible Flight Standards Office, as appropriate. If sending information directly to the Large Aircraft Section, International Validation Branch/manager of the certification office, send it to the attention of the person identified in paragraph (k) of this AD. Information may be emailed to: 9-AVS-AIR-730-AMOC@faa.gov. (2) Contacting the Manufacturer: For any requirement in this AD to obtain instructions from a manufacturer, the instructions must be accomplished using a method approved by the Manager, Large Aircraft Section, International Validation Branch, FAA; or EASA; or Airbus SAS's EASA Design Organization Approval (DOA). If approved by the DOA, the approval must include the DOA-authorized signature. (3) Required for Compliance (RC): Except as required by paragraph (j)(2) of this AD, if any service information referenced in EASA AD 2021-0281 contains paragraphs that are labeled as RC, the instructions in RC paragraphs, including subparagraphs under an RC paragraph, must be done to comply with this AD; any paragraphs, including subparagraphs under those paragraphs, that are not identified as RC are recommended. The instructions in paragraphs, including subparagraphs under those paragraphs, not identified as RC may be deviated from using accepted methods in accordance with the operator's maintenance or inspection program without obtaining approval of an AMOC, provided the instructions identified as RC can be done and the airplane can be put back in an airworthy condition. Any substitutions or changes to instructions identified as RC require approval of an AMOC. (k) Additional Information For more information about this AD, contact Vladimir Ulyanov, Aerospace Engineer, Large Aircraft Section, International Validation Branch, FAA, 2200 South 216th St., Des Moines, WA 98198; telephone and fax: 206-231-3229; email: vladimir.ulyanov@faa.gov. (l) Material Incorporated by Reference (1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51. (2) You must use this service information as applicable to do the actions required by this AD, unless this AD specifies otherwise. (i) European Union Aviation Safety Agency (EASA) AD 2021-0281, dated December 17, 2021. (ii) [Reserved] (3) For EASA AD 2021-0281, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; telephone +49 221 8999 000; email ADs@easa.europa.eu; internet www.easa.europa.eu. You may find this EASA AD on the EASA website at https://ad.easa.europa.eu. (4) You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. (5) You may view this material that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibr-locations.html. Issued on August 10, 2022. Gaetano A. Sciortino, Deputy Director for Strategic Initiatives, Compliance & Airworthiness Division, Aircraft Certification Service.