Adoption of the Amendment
Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0 1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0 2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD) 2010-17-18 R1, Amendment 39-16552 (75 FR 82219, December 30, 2010), and adding the following new AD:
2014-16-17 Air Tractor, Inc.: Amendment 39-17941; Docket No. FAA- 2014-0077; Directorate Identifier 2013-CE-021-AD.
(a) Effective Date
This AD is effective September 29, 2014.
(b) Affected ADs
This AD supersedes AD 2010-17-18 R1, Amendment 39-16552 (75 FR 82219, December 30, 2010, (``AD 2010-17-18 R1'')).
(c) Applicability
This AD applies to Air Tractor, Inc. Models AT-802 and AT-802A airplanes, all serial numbers, that are certificated in any category.
(d) Subject
Joint Aircraft System Component (JASC)/Air Transport Association (ATA) of America Code 57: Wings.
(e) Unsafe Condition
This AD was prompted by our determination that there is a need to establish a safe life for the wing main spar lower caps on all airplanes regardless of configuration or operational use. We are issuing this AD to detect and correct cracks in the wing main spar lower cap at the center splice joint, which could result in failure of the spar cap and lead to wing separation and loss of control of the airplane.
(f) Compliance
Comply with this AD within the compliance times specified in paragraphs (g) through (l) of this AD, including all subparagraphs, unless already done (compliance with AD 2010-17-18 R1).
(g) Actions for Airplanes Serial Numbers (SNs)-0001 Through-0091
(1) Eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks at the compliance times specified in paragraphs (g)(1)(i) or (g)(1)(ii) of this AD. Do the inspections following Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002.
(i) For airplanes previously affected by AD 2010-17-18 R1: Initially inspect upon reaching 1,700 hours time-in-service (TIS) or within the next 50 hours TIS after April 21, 2006 (the effective date retained from AD 2006-08-09, Amendment 39-14565 (71 FR 19994, April 19, 2006; corrected 71 FR 27794, May 12, 2006)), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 800 hours TIS unless you installed the center splice plate and extended 8-bolt splice blocks before September 9, 2010 (the effective date retained from AD 2010-17-18, Amendment 39-16412 (75 FR 52255, August 25, 2010), ``AD 2010-17-18''), then repetitively inspect following the compliance times in paragraphs (g)(5)(i) through (g)(5)(iii) of this AD.
(ii) For airplanes not previously affected by AD 2010-17-18 R1: Initially inspect upon reaching 1,700 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 800 hours TIS unless you installed the center splice plate and extended 8-bolt splice blocks before September 29, 2014 (the effective date of this AD), then repetitively inspect following the compliance times in paragraphs (g)(6)(i) through (g)(6)(iii) of this AD.
(2) If any cracks are found as a result of any inspection required in paragraph (g)(1) of this AD, before further flight after the inspection where a crack was found, do the actions specified in paragraphs (g)(2)(i) or (g)(2)(ii) of this AD. If you repair your airplane following paragraph (g)(2)(i) of this AD before the airplane reaches a total of 3,200 hours TIS, you must do the eddy current inspections following the compliance times in paragraphs (g)(5) and (g)(6) of this AD, as applicable. If you repair your airplane following paragraph (g)(2)(i) of this AD at 3,200 hours TIS or after, this repair terminates the repetitive inspections required in this AD.
(i) For cracks that can be removed by repair, install center splice plate, P/N 20997-2, and extended 8-bolt splice blocks, P/N 20985-1/-2, cold-work the lower spar cap fastener holes, and eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks. This eddy current inspection is required as part of the modification and is separate from the inspections required in paragraph (g)(1) of this AD. Incorporating this repair modification extends the safe life of the wing main spar lower cap to a total of 8,000 hours TIS. Do the repair following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co.
[[Page 50545]]
Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002; Snow Engineering Co. Drawing Number 20995, Sheet 2, Rev. D., dated November 25, 2005; and Snow Engineering Co. Service Letter 240, dated September 30, 2004.
(ii) For cracks that cannot be repaired by incorporating the repair modification specified in paragraph (g)(2)(i) of this AD, replace the lower spar caps and associated parts listed following paragraph (g)(3) of this AD.
(3) Replace the wing main spar lower caps, the web plates, the center joint splice blocks and hardware, and the wing attach angles and hardware, and install the steel web splice plate at whichever of the compliance times specified in paragraphs (g)(3)(i), (g)(3)(ii), or (g)(3)(iii) of this AD that occurs first. If the wing main spar lower cap was replaced with P/N 21118-1/-2, the new spar safe life is 11,700 hours TIS. If the wing main spar lower cap is replaced with P/N 21083-1/-2 before September 9, 2010 (the effective date retained from AD 2010-17-18), the safe life for that P/N spar cap is 8,000 hours TIS until the wing main spar lower cap is replaced with P/N 21118-1/-2. This replacement terminates the inspections required in this AD. Do the replacement following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co. Service Letter 80GG, revised December 21, 2005; and Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A, dated January 7, 2009.
(i) For all airplanes: Before further flight when cracks are found that cannot be repaired by incorporating the repair modification specified in paragraph (g)(2)(i) of this AD.
(ii) For airplanes previously affected by AD 2010-17-18 R1: Before or when the airplane reaches the wing main spar lower cap safe life of a total of 4,100 hours TIS or within the next 50 hours TIS after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later.
(iii) For airplanes not previously affected by AD 2010-17-18 R1: Before or when the airplane reaches the wing main spar lower cap safe life of a total of 4,100 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later.
(4) To extend the initial 4,100-hour TIS safe life of the wing main spar lower cap to a total of 8,000 hours TIS, you may incorporate the repair modification specified in paragraph (g)(2)(i) of this AD between 3,200 hours TIS and 4,100 hours TIS. This modification terminates the repetitive inspections required in paragraphs (g)(1)(i) and (g)(1)(ii) of this AD, unless you do the modification before the airplane reaches a total of 3,200 hours TIS to repair cracks.
(5) For airplanes previously affected by AD 2010-17-18 R1: If you modified your airplane to repair cracks before the airplane reached a total of 3,200 hours TIS, as required in paragraph (g)(2)(i) of this AD, or you previously modified your wing to extend the safe life but did not cold work the lower spar cap fastener holes, you must do the eddy current inspections required in paragraph (g)(1) of this AD following the compliance times specified in paragraphs (g)(5)(i) through (g)(5)(iii) of this AD, as applicable.
(i) If the airplane already had the center splice plate and extended 8-bolt splice blocks installed at or after 3,200 hours TIS but the fastener holes have not been cold worked, you may cold work the fastener holes at any time to terminate the repetitive inspection requirements of this paragraph. Initially inspect when the airplane reaches a total of 2,400 hours TIS after the modification or within the next 100 days after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 1,200 hours TIS until the 8,000 hours TIS spar replacement time.
(ii) If the airplane already had the center splice plate and extended 8-bolt splice blocks already installed before reaching 3,200 hours TIS but the fastener holes have not been cold worked, initially inspect when the airplane reaches a total of 2,400 hours TIS after the modification or within the next 100 days after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 1,200 hours TIS. Upon reaching 4,800 hours TIS after the modification, repetitively thereafter inspect at intervals not to exceed 600 hours TIS until the 8,000 hours TIS spar replacement time.
(iii) If the airplane had the center splice plate and extended 8-bolt splice blocks installed before reaching 3,200 hours TIS and the fastener holes have been cold worked, initially inspect when the airplane reaches a total of 4,800 hours TIS after the modification or within the next 100 days after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later. Repetitively thereafter inspect at intervalsnot to exceed 600 hours TIS until the 8,000 hours TIS spar replacement time.
(6) For airplanes not previously affected by AD 2010-17-18 R1: If you modified your airplane to repair cracks before the airplane reached a total of 3,200 hours TIS, as required in paragraph (g)(2)(i) of this AD, or you previously modified your wing to extend the safe life but did not cold work the lower spar cap fastener holes, and your, you must do the eddy current inspections required in paragraph (g)(1) of this AD following the compliance times specified in paragraphs (g)(6)(i) through (g)(6)(iii) of this AD, as applicable.
(i) If the airplane already had the center splice plate and extended 8-bolt splice blocks installed at or after 3,200 hours TIS but the fastener holes have not been cold worked, you may cold work the fastener holes at any time to terminate the repetitive inspection requirements of this paragraph. Initially inspect when the airplane reaches a total of 2,400 hours TIS after the modification or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 1,200 hours TIS until the 8,000 hours TIS spar replacement time.
(ii) If the airplane had the center splice plate and extended 8- bolt splice blocks already installed before reaching 3,200 hours TIS but the fastener holes have not been cold worked, initially inspect when the airplane reaches a total of 2,400 hours TIS after the modification or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 1,200 hours TIS. Upon reaching 4,800 hours TIS after the modification, repetitively thereafter inspect at intervals not to exceed 600 hours TIS until the 8,000 hours TIS spar replacement time.
(iii) If the airplane had the center splice plate and extended 8-bolt splice blocks installed before reaching 3,200 hours TIS and the fastener holes have been cold worked, initially inspect when the airplane reaches a total of 4,800 hours TIS after the modification or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 600 hours TIS until the 8,000 hours TIS spar replacement time.
(7) If you find any cracks during any inspection required by paragraphs (g)(5) and (g)(6) of this AD, before further flight, replace the lower spar caps and the associated parts following the procedures identified in paragraph (g)(3) of this AD.
(h) Actions for Airplanes SNs-0092 Through -0101
(1) Eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks at the compliance times specified in paragraphs (h)(1)(i) or (h)(1)(ii) of this AD. Do the inspections following Snow Engineering Co. Service Letter 284, dated October 4, 2009; and Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002.
(i) For airplanes previously affected by AD 2010-17-18 R1: Initially inspect upon reaching 1,700 hours TIS or within the next 50 hours TIS after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 800 hours TIS unless the center splice plate, P/N 20994-2, is installed, then repetitively inspect at intervals not to exceed 2,000 hours TIS.
(ii) For airplanes not previously affected by AD 2010-17-18 R1: Initially inspect upon reaching 1,700 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 800 hours TIS unless the center splice plate, P/N 20994-2, is installed, then repetitively inspect at intervals not to exceed 2,000 hours TIS.
(2) If any cracks are found as a result of any inspection required by paragraph (h)(1) of this AD, before further flight after the inspection where a crack was found, do the actions specified in paragraphs (h)(2)(i) or (h)(2)(ii) of this AD.
(i) For cracks that can be removed by repair, install the 9-bolt splice blocks, cold-work the lower spar cap fastener holes, install the center splice plate, P/N 20994-2,
[[Page 50546]]
if not already installed, and eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks. This eddy current inspection is required as part of the repair and is separate from the inspections required in paragraph (h)(1) of this AD. Incorporating this repair modification extends the safe life of the wing main spar lower cap to a total of 8,000 hours TIS and terminates the repetitive inspections required in this AD. Do therepair following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002; Snow Engineering Co. Service Letter 281, dated August 1, 2009; and Snow Engineering Co. Drawing Number 20995, Sheet 3, dated November 25, 2005.
(ii) For cracks that cannot be repaired by incorporating the repair modification specified in paragraph (h)(2)(i) of this AD, replace the lower spar caps and associated parts listed following paragraph (h)(3) of this AD.
(3) Replace the wing main spar lower caps, the web plates, the center joint splice blocks and hardware, and the wing attach angles and hardware, and install the steel web splice plate at whichever of the compliance times specified in paragraphs (h)(3)(i), (h)(3)(ii), or (h)(3)(iii) of this AD that occurs first. If the wing main spar lower cap is replaced with P/N 21118-1/-2, the new spar safelife is 11,700 hours TIS. If the wing main spar lower cap was replaced with P/N 21083-1/-2 before September 9, 2010 (the effective date retained from AD 2010-17-18), the safe life for that P/N spar cap is 8,000 hours TIS until the wing main spar lower cap is replaced with P/N 21118-1/-2. This replacement terminates the inspections required in this AD. Do the replacement following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co. Service Letter 80GG, revised December 21, 2005; and Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A, dated January 7, 2009.
(i) For all airplanes: Before further flight when cracks are found that cannot be repaired by incorporating the modification specified in paragraph (h)(2)(i) of this AD.
(ii) For airplanes previously affected by AD 2010-17-18 R1: Before or when the airplane reaches the wing main spar lower cap safe life of a total of 4,100 hours TIS or within the next 50 hours TIS after September 9, 2010(the effective date retained from AD 2010-17-18), whichever occurs later.
(iii) For airplanes not previously affected by AD 2010-17-18 R1: Before or when the airplane reaches the wing main spar lower cap safe life of a total of 4,100 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later.
(4) To extend the initial 4,100-hour TIS safe life of the wing main spar lower cap to a total of 8,000 hours TIS, before the airplane reaches a total of 4,100 hours TIS, as long as no cracks are found during any inspection required in paragraph (h)(1) of this AD, install center splice plate, P/N 20994-2, if not already installed as part of a repair, cold-work the lower spar cap fastener holes, and eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks. This eddy current inspection is required as part of the modification and is separate from the inspections required in paragraph (h)(1) of this AD. After installing P/N 20994-2, eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks repetitively at intervals not to exceed 2,000 hours TIS following the procedures specified in paragraph (h)(1) of this AD. Do the modification following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002; Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A., dated January 7, 2009; and Snow Engineering Co. Service Letter 245, dated April 25, 2005.
(i) For airplanes previously affected by AD 2010-17-18 R1: As of September 9, 2010 (the effective date retained from AD 2010-17-18), if you have already exceeded the 4,100-hour TIS threshold for extending the safe life to 8,000 hours TIS, you may be eligiblefor an alternative method of compliance following paragraph (o) in this AD.
(ii) For airplanes not previously affected by AD 2010-17-18 R1: As of September 29, 2014 (the effective date of this AD), if you have already exceeded the 4,100-hour TIS threshold for extending the safe life to 8,000 hours TIS, you may be eligible for an alternative method of compliance following paragraph (o) in this AD.
(5) If any cracks are found as a result of the eddy current inspection required by paragraph (h)(4) of this AD, do the actions specified in paragraphs (h)(5)(i) or (h)(5)(ii) of this AD.
(i) For cracks that can be removed by repair, install the 9-bolt splice blocks, cold-work the lower spar cap fastener holes, and eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks. This eddy current inspection is required as part of the modification and is separate from the inspections required in paragraph (h)(1) of this AD. Incorporating this repair modification terminates the repetitive inspections required in paragraph (h)(4) of this AD. Do the repair following Snow Engineering Co. Service Letter 284, dated October 4, 2009; and Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002; Snow Engineering Co. Service Letter 281, dated August 1, 2009; and Snow Engineering Co. Drawing Number 20995, Sheet 3, dated November 25, 2005.
(ii) For cracks that cannot be repaired by incorporating the repair modification specified in paragraph (h)(5)(i) of this AD, replace the lower spar caps and associated parts listed following paragraph (h)(3) of this AD.
(i) Actions for Airplanes SNs-0102 through -0178
(1) For airplanes previously affected by AD 2010-17-18 R1: Eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks atthe compliance times specified in paragraphs (i)(1)(i) and (i)(1)(ii) of this AD, as applicable. Do the inspections following Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002; Snow Engineering Co. Service Letter 245 dated April 25, 2005; Snow Engineering Co. Service Letter 284, dated October 4, 2009.
(i) If the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps have not been cold worked, initially inspect when the airplane reaches a total of 5,500 hours TIS or within the next 50 hours TIS after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 1,100 hours TIS until the 8,000 hours TIS spar replacement time.
(ii) If the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps have been cold worked, initially inspect when the airplane reaches a total of 5,500 hours TIS or within the next 50 hours TIS after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 2,200 hours TIS until the 8,000 hours TIS spar replacement time.
(2) For airplanes not previously affected by AD 2010-17-18 R1: Eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks at the compliance times specified in paragraphs (i)(2)(i) and (i)(2)(ii) of this AD, as applicable. Do the inspections following Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002; Snow Engineering Co. Service Letter 245 dated April 25, 2005; Snow Engineering Co. Service Letter 284, dated October 4, 2009.
(i) If the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps have not been cold worked, initially inspect when the airplane reaches a total of 5,500 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 1,100 hours TIS until the 8,000 hours TIS spar replacement time.
(ii) If the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps have been cold worked initially inspect when the airplane reaches a total of 5,500 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later. Repetitively thereafter inspect at intervals not to exceed 2,200 hours TIS until the 8,000 hours TIS spar replacement time.
(3) If no cracks are found during the initial inspections required in paragraphs (i)(1)(i)
[[Page 50547]]
and (i)(2)(i) of this AD, to use thelonger repetitive inspection intervals specified in paragraphs (i)(1)(ii) and (i)(2)(ii) of this AD, as applicable, you may do the optional cold-working of the lower spar cap fastener holes following Snow Engineering Co. Service Letter 245, dated April 25, 2005.
(4) If any cracks are found during any inspection required in paragraphs (i)(1) and (i)(2) of this AD, before further flight after the inspection where a crack is found, do the actions specified in paragraphs (i)(4)(i) or (i)(4)(ii) of this AD.
(i) For cracks that can be removed by repair, install the 9-bolt splice blocks, cold-work the lower spar cap fastener holes, and eddy current inspect the center splice joint outboard two fastener holes in both the left and right wing main spar lower caps for cracks. This eddy current inspection is required as part of the repair modification and is separate from the inspections required in paragraphs (i)(1) and (i)(2) of this AD. This modification terminates the repetitive inspections required in this AD. Do the repair following Snow Engineering Co. Service Letter 281, dated August 1, 2009; and Snow Engineering Co. Drawing Number 20995, Sheet 3, dated November 25, 2005.
(ii) For cracks that cannot be repaired by doing the actions specified in paragraph (i)(4)(i) of this AD, replace the lower spar caps and associated parts listed following paragraph (i)(5) of this AD, including all subparagraphs.
(5) Replace the wing main spar lower caps, the web plates, the center joint splice blocks and hardware, and the wing attach angles and hardware, and install the steel web splice plate at whichever of the compliance times specified in paragraphs (i)(5)(i), (i)(5)(ii), or (i)(5)(iii) of this AD that occurs first. This replacement terminates the inspections required in this AD, including all subparagraphs. After this replacement the new spar safe life is 11,700 hours TIS. Do the replacement following Snow Engineering Co. Service Letter 284, dated October 4, 2009; SnowEngineering Co. Service Letter 80GG, revised December 21, 2005; Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A, dated January 7, 2009.
(i) For all airplanes: Before further flight when cracks are found that cannot be repaired by doing the actions specified in paragraph (i)(4)(i) of this AD.
(ii) For airplanes previously affected by AD 2010-17-18 R1: Before or when the airplane reaches the wing main spar lower cap safe life of a total of 8,000 hours TIS or within the next 50 hours TIS after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later.
(iii) For airplanes not previously affected by AD 2010-17-18 R1: Before or when the airplane reaches the wing main spar lower cap safe life of a total of 8,000 hours TIS or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later.
(j) Actions for Airplanes SNs-0179 Through -0269
Replace the wing main spar lower caps, the web plates, the center joint splice blocks and hardware, and the wing attach angles and hardware, and install the steel web splice plate at the compliance times specified in paragraphs (j)(1) or (j)(2) of this AD. Do the replacement following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co. Service Letter 80GG, revised December 21, 2005; and Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A, dated January 7, 2009. After this replacement the new spar safe life is 11,700 hours TIS.
(1) For airplanes previously affected by AD 2010-17-18 R1: Unless already done (compliance with AD 2010-17-18 R1), by the 8,000-hour TIS safe life, or within the next 50 hours TIS after September 9, 2010 (the effective date retained from AD 2010-17-18), whichever occurs later.
(2) For airplanes not previously affected by AD 2010-17-18 R1: Unless already done, by the 8,000-hour TIS safe life, or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later.
(k) Actions for Airplanes S/Ns-0270 and Subsequent Not Affected by AD 2010-17-18 R1
(1) As of September 29, 2014 (the effective date of this AD), this action establishes the safe life for the wing main spar to be 11,700 hours TIS.
(2) Upon reaching the 11,700-hour TIS safe life or within the next 50 hours TIS after September 29, 2014 (the effective date of this AD), whichever occurs later, replace the wing main spar lower caps, the web plates, the center joint splice blocks and hardware, and the wing attach angles and hardware, and install the steel web splice plate. After this replacement the subsequent new spar safe life is 11,700 hours TIS. Do the replacement following Snow Engineering Co. Service Letter 284, dated October 4, 2009; Snow Engineering Co. Service Letter 80GG, revised December 21, 2005; and Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A, dated January 7, 2009.
(l) Reporting Requirement for All Airplanes
Report any crack from any inspection required in paragraphs (g) through (i) of this AD within 30 days after any crack is found using the form in Figure 1 of this AD. Send your report to Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o San Antonio MIDO), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; phone: (210) 308-3365; fax: (210) 308-3370. BILLING CODE 4910-13-P
[[Page 50548]]
[GRAPHIC] [TIFF OMITTED] TR25AU14.003
BILLING CODE 4910-13-C
(m) Special Flight Permit
Special flight permits are permitted in accordance with 14 CFR 39.23 provided the following limitations are adhered to:
(1) Only operate in day visual flight rules (VFR).
(2) Ensure that the hopper is empty.
(3) Limit airspeed to 135 miles per hour (mph) indicated airspeed (IAS).
(4) Avoid any unnecessary g-forces.
(5) Avoid areas of turbulence.
(6) Plan the flight to follow the most direct route.
(n) Paperwork Reduction Act Burden Statement
A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the
[[Page 50549]]
requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200.
(o) Alternative Methods of Compliance (AMOCs)
(1) The Manager, Fort Worth Airplane Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in paragraph (p) of this AD.
(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.
(3) AMOCs approved for AD 2010-17-18 R1 are approved as AMOCs for this AD.
(p) Related Information
For more information about this AD, contact Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o San Antonio MIDO), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; phone: (210) 308-3365; fax: (210) 308-3370; email: andrew.mcanaul@faa.gov.
(q) Material Incorporated by Reference
(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise.
(3) The following service information was approved for IBR on September 9, 2010 (75 FR 52255, August 25, 2010).
(i) Snow Engineering Co. Service Letter 80GG, dated December 21, 2005.
(ii) Snow Engineering Co. Service Letter 284, dated October 4, 2009.
(iii) Snow Engineering Co. Service Letter 281, dated August 1, 2009.
(iv) Snow Engineering Co. Service Letter 245, dated April 25, 2005.
(v) Snow Engineering Co. Drawing Number 20995, Sheet 2, Rev. D., dated November 25, 2005.
(vi) Snow Engineering Co. Drawing Number 20995, Sheet 3, dated November 25, 2005.
(vii) Snow Engineering Co. Drawing Number 20975, Sheet 4, Rev. A.,dated January 7, 2009
(4) The following service information was approved for IBR on April 21, 2006 (71 FR 19994, April 19, 2006).
(i) Snow Engineering Co. Process Specification 197, page 1, revised June 4, 2002; pages 2 through 4, dated February 23, 2001; and page 5, dated May 3, 2002.
(ii) Snow Engineering Co. Service Letter 240, dated September 30, 2004.
(5) For Air Tractor, Inc. service information identified in this AD, contact Air Tractor, Inc., P.O. Box 485, Olney, Texas 76374; telephone: (940) 564-5616; fax: (940) 564-5612; email: airmail@airtractor.com; Internet: www.airtractor.com.
(6) You may view this service information at FAA, Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the FAA, call 816-329-4148.
(7) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of thismaterial at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html.