AD 2008-10-02

Active

Part number identification placard

Key Information
2008-10-02
Active
May 12, 2008
April 28, 2008
FAA-2008-0471
39-15508
Applicability
["Aircraft"]
["Small Airplane"]
Cessna Aircraft Company
172 172R 172RG 172S 175 180 182 182S 182T 185 206 206H 207 208 208B 210 210-5 (205) F172D F172E F172F F172G F172H F172K F172L F172M F172N F172P F182P F182Q FR172E FR172F FR172G FR172H FR172J FR172K FR182 P172D P206 R172E R172F R172G R172H R172J R172K R182 T182 T182T T206H T210F T210G T210H T210J T210K T210L T210M T210N T210R T303 TR182 TU206A TU206B TU206C TU206D TU206E TU206F TU206G U206
Summary

The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of improper installation of the part number identification placard on the alternate static air source selector valve. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control.

Action Required

Final rule; request for comments.

Regulatory Text

2008-10-02 Cessna Aircraft Company: Amendment 39-15508; Docket No. FAA-2008-0471; Directorate Identifier 2008-CE-025-AD. \n\nEffective Date \n\n\t(a) This AD becomes effective on May 12, 2008. \n\nAffected ADs \n\n\t(b) None. \n\nApplicability \n\n\t(c) This AD applies to airplanes listed in Table 1 and Table 2 of this AD that: \n\n\t(1) Have a part number (P/N) 2013142-18 alternate static air source selector valve installed after November 19, 2007; and \n\n\t(2) Are certificated in any category: \n\n\tTable 1.--Applicability for Airplanes That Had the Affected Part Installed at Manufacture\n\nModel \nSerial Nos. (S/Ns) \n172S \n172S10672 through 172S10674, 172S10676, 172S10678 through 172S10680, 172S10682, 172S10683, and 172S10685. \n182T \n18282062 and 18282065. \nT182T \nT18208822 and T18208828. \n208 \n20800417, 20800418, and 20800419. \n208B \n208B1294 through 208B1310. \n\n\n\tNote 1: Airplanes listed in Table 1 may have also had the affected part installed as a replacement part.Table 2.--Applicability for Airplanes That Could Have Had the Affected \n\tPart Installed as a Replacement Part or From Parts Held as Spares\n\n\nModel \nS/Ns \n172\nAll S/Ns. \n172R\nAll S/Ns beginning with 17280001. \n172S\n172S8001 through 172S10671. \nF172D\nAll S/Ns. \nF172E\nAll S/Ns. \nF172F\nAll S/Ns. \nF172G\nAll S/Ns. \nF172H\nAll S/Ns. \nF172K\nAll S/Ns. \nF172L\nAll S/Ns. \nF172M\nAll S/Ns. \nF172N\nAll S/Ns. \nF172P\nAll S/Ns. \nFR172E\nAll S/Ns. \nFR172F\nAll S/Ns. \nFR172G\nAll S/Ns. \nFR172H\nAll S/Ns. \nFR172J\nAll S/Ns. \nFR172K\nAll S/Ns. \nP172D\nAll S/Ns. \nR172E (USAF T-41B) (USAF T-41C and D). \nAll S/Ns. \nR172F (USAF T-41). \nAll S/Ns. \nR172G (USAF T-41C or D). \nAll S/Ns. \nR172H (USAF T-41D). \nAll S/Ns. \nR172J\nAll S/Ns. \nR172K\nAll S/Ns. \n172RG\nAll S/Ns. \n175\nAll S/Ns. \n180\nAll S/Ns. \n182\nAll S/Ns. \n182S\n18280001 through 18280944. \n182T\n18280945 through 18282061. \nR182\nAll S/Ns. \nT182\nAll S/Ns. \nTR182\nAll S/Ns. \nT182T\nT18208001 through T18208821. \nF182P\nAll S/Ns. \nF182Q\nAll S/Ns. \nFR182\nAll S/Ns. \n185\nAll S/Ns. \n206\nAll S/Ns. \n206H\nAll S/Ns beginning with 20608001. \nP206\nAll S/Ns. \nU206\nAll S/Ns. \nT206H\nAll S/Ns beginning with T20608001. \nTU206A\nAll S/Ns. \nTU206B\nAll S/Ns. \nTU206C\nAll S/Ns. \nTU206D\nAll S/Ns. \nTU206E\nAll S/Ns. \nTU206F\nAll S/Ns. \nTU206G\nAll S/Ns \n207\nAll S/Ns. \n208\n20800001 through 20800416. \n208B\n208B0001 through 208B1293. \n210\nAll S/Ns. \n210-5 (205). \nAll S/Ns. \nT210F\nAll S/Ns. \nT210G\nAll S/Ns. \nT210H\nAll S/Ns. \nT210J \nAll S/Ns. \nT210K\nAll S/Ns. \nT210L\nAll S/Ns. \nT210M\nAll S/Ns. \nT210N\nAll S/Ns. \nT210R\nAll S/Ns. \nT303\nAll S/Ns. \n\n\n\tNote 2: P/N 2013142-18 replaced P/Ns 2013142-9, -13, and -17. \n\nUnsafe Condition \n\n\t(d) This AD is the result of reports of improper installation of the part number identification placard on the alternate static air source selector valve. We are issuing this AD to prevent erroneous indications from thealtimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control. \n\nCompliance \n\n\t(e) For all affected airplanes, to address this problem, you must do the following, unless already done: \n\n\nActions \nCompliance \nProcedures \n(1) Inspect the alternate static air source selector valve to assure that the part number identification placard is not obstructing the port. \n(i) For static air source selector valves installed before May 12, 2008 (The effective date of this AD): Before further flight after May 12, 2008 (the effective date of this AD), and \n(ii) For static air source selector valves installed as modification or replacement parts on or after May 12, 2008 (the effective date of this AD): Before further flight after installation of a P/N 2013142-18 alternate static air source selector valve. Inspection of the part before installation is acceptable. \n(A) Adjust the pilot and copilot seats as far aft as possible. \n(B) Use a flashlight and mirror to inspect the alternate static air source selector valve to assure the port on the forward end of the valve is clearly visible and not covered by the part number identification placard. \n(2) If the alternate static air source selector valve port is found obstructed by the part number identification placard during any inspection required by paragraph (e)(1) of this AD, remove the placard from the valve body, discard the placard, and assure that the port is open and unobstructed. \nBefore further flight after any inspection required in paragraph (e)(1) of this AD where the port is found obstructed. \nMake an entry in the aircraft records showing compliance with this portion of the AD following 14 CFR 43.9. \n\n\n\t(f) Report the results of the inspection required by this AD where an obstruction was found to the FAA. \n\n\t(1) Submit this report within 10 days after the inspection or 10 days after the effective date of this AD, whichever occurs later. \n\n\t(2) Use the form in Figure 1 of this AD and submit it to FAA, Manufacturing Inspection District Office, Mid-Continent Airport, 1804 Airport Road, Room 101, Wichita, Kansas, 67209; or fax to (316) 946-4189. \n\n\t(3) The Office of Management and Budget (OMB) approved the information collection requirements contained in this regulation under the provisions of the Paperwork Reduction Act of 1980 (44 U.S.C. 3501 et seq.) and assigned OMB Control Number 2120-0056. \n\n\n\nAlternative Methods of Compliance (AMOCs) \n\n\t(g) The Manager, Wichita Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to: Attn: David Fairback, Aerospace Engineer, FAA, Wichita ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946- 4154; fax: 316-946-4107; e-mail address: david.fairback@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

Supplementary Information

Discussion \n\n\tWe recently received reports of improper installation of the part number identification placard on alternate static air source selector valves of certain Cessna 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes. The part number identification placard refers to alternative air source selector valves, part number 2013142-18 that were manufactured between November 20, 2007, and February 18, 2008. The part number identification placard was installed on the valve body in a location that covers the port, which is the inlet for static air reference into the valve. The problem was discovered during a quality control check. \n\n\tAll parts held in stock at Cessna have been corrected. Cessna has no way of verifying how many of these assemblies were manufactured and sent to the field with the part number identification placard installed over the alternate static air source selector valve port. \n\n\tWe have no way of determining which airplanes have the remaining problem alternate static air source selector valve assemblies installed without having all of the affected airplanes and spares stock inspected. \n\n\tThis condition, if not corrected, could result in the altimeter, airspeed, and vertical speed indicators displaying erroneous indications. This could cause the pilot to react to incorrect flight information and possibly result in loss of control. \n\nFAA's Determination and Requirements of This AD \n\n\tWe are issuing this AD because we evaluated all the information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This AD requires inspecting the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. \n\n\tIn preparing this rule, we contacted type clubs and aircraft operators to get technical information and information on operational and economic impacts. We have included a discussion of information that may have influenced this action in the rulemaking docket. \n\nFAA's Determination of the Effective Date \n\n\tAn unsafe condition exists that requires the immediate adoption of this AD. The FAA has found that the risk to the flying public justifies waiving notice and comment prior to adoption of this rule because erroneous indications from the altimeter, airspeed, and vertical speed indicators could cause the pilot to react to incorrect flight information and possibly result in loss of control. Therefore, we determined that notice and opportunity for public comment before issuing this AD are impracticable and that good cause exists for making this amendment effective in fewer than 30 days. \n\nComments Invited \n\n\tThisAD is a final rule that involves requirements affecting flight safety, and we did not precede it by notice and an opportunity for public comment. We invite you to send any written relevant data, views, or arguments regarding this AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number "FAA-2008-0471; Directorate Identifier 2008-CE-025-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the AD. We will consider all comments received by the closing date and may amend the AD in light of those comments. \n\n\tWe will post all comments we receive, without change, to http:// www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this AD. \n\nAuthority for This Rulemaking \n\n\tTitle 49 of the United States Code specifies the FAA's authority to issue ruleson aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority. \n\n\tWe are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. \n\nRegulatory Findings \n\n\tWe determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. \n\n\tFor the reasons discussed above, I certify that this AD: \n\n\t(1) Is not a "significant regulatory action" under Executive Order 12866; \n\n\t(2) Is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and \n\n\t(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. \n\n\tWe prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. \n\nExamining the AD Docket \n\n\tYou may examine the AD docket that contains the AD, the regulatory evaluation, any comments received, and other information on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5527) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. \n\nList of Subjects in 14 CFR Part 39 \n\n\tAir transportation, Aircraft, Aviation safety, Safety. \n\nAdoption of the Amendment \n\nAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n1. The authority citation for part 39 continues to read as follows: \n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\nSec. 39.13 (Amended) \n\n2. The FAA amends Sec. 39.13 by adding the following new airworthiness directive (AD):

AD Assistant

Get AI-powered answers about this AD, check applicability, and find compliance steps.

Sign Up to Unlock
Contact Information

David Fairback, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4154; fax: 316-946-4107; e-mail address: david.fairback@faa.gov.

References
(Federal Register: May 2, 2008 (Volume 73, Number 86))
--- - Part 39
(Page 24168-24171)
FAA Documents