AD 2008-02-14

The FAA is adopting a new airworthiness directive (AD) for certain Boeing airplanes listed above. This AD requires an inspection of certain lighted pushbutton switches in the flight compartment for configuration 'D' master modules and part numbers and corrective action if necessary. This AD also provides an option to inspect panel assemblies for part numbers. This AD results from a report indicating that the integrated drive generator failed in flight due to a possible switch malfunction. We are issuing this AD to ensure that certain lighted pushbutton switches in the flight compartment do not malfunction and cause the flightcrew to be unable to control critical airplane systems and continue safe airplane operation.

Final rule.

2008-02-14 Boeing: Amendment 39-15344. Docket No. FAA-2007-28973; Directorate Identifier 2007-NM-118-AD. \n\nEffective Date \n\n\t(a) This AD becomes effective February 28, 2008. \n\nAffected ADs \n\n\t(b) None. \n\nApplicability \n\n\t(c) This AD applies to Boeing airplanes listed in Table 1 of this AD, certificated in any category. \n\n\tTable 1.--Applicability \n\n\nModel - \nAs Identified in Boeing Alert Service Bulletin - \n747-400, -400D, and -400F series airplanes\n747-33A2280, Revision 1, dated September 25, 2003\n757-200, -200CB, and -200PF series airplanes\n757-33A0044, Revision 1, dated September 25, 2003\n757-300 series airplanes\n757-33A0045, Revision 1, dated September 25, 2003\n767-200, -300, and -300F series airplanes\n767-33A0087, Revision 1, dated September 25, 2003\n767-400ER series airplanes\n767-33A0088, including Appendix A, dated December 19, 2001\n\n\nUnsafe Condition \n\n\t(d) This AD results from a report indicating that the integrated drive generator (IDG) failed in flight due to possible switch malfunction. We are issuing this AD to ensure that certain lighted pushbutton switches in the flight compartment do not malfunction and cause the flightcrew to be unable to control critical airplane systems and continue safe airplane operation. \n\nCompliance \n\n\t(e) You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. \n\nService Bulletin References \n\n\t(f) The term "the service bulletin,'' as used in this AD, means the Accomplishment Instructions of the service bulletins listed in Table 1 of this AD, as applicable. \n\n\tNote 1: The Boeing service bulletins refer to Korry Service Bulletin 433-33-05, dated July 23, 2001, as an additional source of service information for finding configuration 'D' switches, for replacing the switch master module with a configuration 'D' master module, and for doing various operational tests after the replacement.Component Service Bulletin References \n\n\t(g) The Boeing service bulletins listed in Table 1 of this AD refer to the Boeing component service bulletins specified in Table 2 of this AD as additional sources of service information for replacing the switch or switch master module at critical locations, for doing operational tests after the replacement, and for identifying new panel part numbers. \n\n\n\tTable 2.--Boeing Component Service Bulletins: Secondary Sources of Service Information \n\n\n\nBoeing Component Service Bulletin -\nDate -\nModel -\nCritical Location -\n233N3203-21-01, Revision 1\nSeptember 25, 2003\n757 airplanes\nEquipment Cooling Panel\n233N3204-30-02, Revision 1\nSeptember 25, 2003\n757 airplanes\nAnti-ice Panel\n233N3206-28-02, Revision 1\nSeptember 25, 2003\n757-200, -200CB, and -200PF series airplanes\nFuel Control Panel \n233N3209-24-03, Revision 1\nSeptember 25, 2003\n757 airplanes and 767-200, -300, and -300F series airplanes\nElectrical Systems Panel \n233N3211-24-02, Revision 1\nSeptember 25, 2003\n757 airplanes and 767 airplanes\nBattery/Standby Power Panel \n233N3215-36-01, Revision 1\nSeptember 25, 2003\n757 airplanes\nBleed Air Panel Assembly\n233N3216-22-01, Revision 1\nSeptember 25, 2003\n757 airplanes and 767 airplanes\nYaw Damper Panel Assembly\n233N3219-33-01, including Appendix A\nDecember 19, 2001\n757-200, -200CB, and -200PF series airplanes\nEmergency Lights/Passenger Oxygen Panel\n233N3223-31-03, Revision 1\nSeptember 25, 2003\n757 airplanes\nEngine Start/Ram Air Turbine Panel Assembly\n233N3224-73-01, Revision 1\nSeptember 25, 2003\n757-200, -200CB, and -200PF series airplanes\nElectronic Engine Control Power Panel Assembly\n233N6203-26-10, Revision 1\nSeptember 25, 2003\n757 airplanes and 767-200, -300, and -300F series airplanes\nAuxiliary Power Unit/Cargo Fire Control Panel Assembly\n233T3210-33-01, Revision 1\nSeptember 25, 2003\n757 airplanes and 767 airplanes\nEmergency Lights Panel\n233T3215-24-01, including AppendixA\nDecember 19, 2001\n767-400ER series airplanes\nElectrical Control Module Assembly\n233T3235-28-05, Revision 1\nSeptember 25, 2003\n767-200, -300, and -300F series airplanes\nFuel Management Panel Assembly\n233T3236-21-05, Revision 1\nSeptember 25, 2003\n767 airplanes\nTemperature Control Panel \n233T3237-36-04, Revision 1\nSeptember 25, 2003\n767 airplanes\nBleed Air Control Panel\n233T3241-30-03, Revision 1\nSeptember 25, 2003\n757-200, -200CB, and -200PF series airplanes, and 767-200, -300, and -300F series airplanes\nWing and Engine Anti-ice Control Panel\n233T3242-73-02, Revision 1\nSeptember 25, 2003\n757 airplanes and 767-200, -300, and -300F series airplanes\nElectronic Engine Control Panel\n233T3244-74-03, Revision 1\nSeptember 25, 2003\n767 airplanes\nEngine Ignition and Start Control Panel\n233T6211-26-01, including Appendix A\nDecember 19, 2001\n767-400ER series airplanes\nAuxiliary Power Unit and Cargo Fire Control Module Assembly\n233U3201-30-04, Revision 1\nSeptember 25, 2003\n747-400, -400D, and -400F series airplanes\nRain Removal/ Anti-ice Module \n233U3202-24-02, Revision 1\nSeptember 25, 2003\n747-400, -400D, and -400F series airplanes\nElectrical and Standby Power/ Auxiliary Power Unit Start Module\n233U3203-36-01, Revision 1\nSeptember 25, 2003\n747-400, -400D, and -400F series airplanes\nBleed Air Control Module\n233U3206-28-01, Revision 1\nSeptember 25, 2003\n747-400, -400D, and -400F series airplanes\nEngine Ignition Control/Fuel Jettison Module\n233U3208-22-02, Revision 1\nSeptember 25, 2003\n747-400, -400D, and -400F series airplanes\nPassenger Oxygen and Yaw Damper Module\n233U3214-26-06, Revision 1\nSeptember 25, 2003\n747-400, -400D, and -400F series airplanes\nFire Control Module\n257U0002-32-04, including Appendix A\nDecember 19, 2001\n747-400, -400D, and -400F series airplanes\nLanding Gear Actuator Control Lever Module Assembly\n\n\nInspection \n\n\t(h) Within 60 months after the effective date of this AD: Do a general visual inspection of the switches specified in paragraphs (h)(1), (h)(2), (h)(3), (h)(4), and (h)(5) of this AD, as applicable, to identify configuration 'D' master modules and the part number (P/N) of the switch, in accordance with the applicable service bulletin, except as provided by paragraph (i) of this AD. \n\n\tNote 2: For the purposes of this AD, a general visual inspection is "A visual examination of a interior or exterior area, installation or assembly to detect obvious damage, failure or irregularity. This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to ensure visual access to all surfaces in the inspection area. This level of inspection is made under normal available lighting conditions such as daylight, hangar lighting, flashlight or drop- light and may require removal or opening of access panels or doors. Stands, ladders or platforms may be required to gain proximity to the area being checked.'' \n\n\t(1) For Model 757-200, -200CB, and -200PF series airplanes: Switches identified in step 1 and step 3 of Figure 1 of Boeing Alert Service Bulletin 757-33A0044, Revision 1, dated September 25, 2003. \n\t(2) For Model 757-300 series airplanes: Switches identified in step 1 of Figure 1 of Boeing Alert Service Bulletin 757-33A0045, Revision 1, dated September 25, 2003. \n\t(3) For Model 767-200, -300, and -300F series airplanes: Switches identified in step 1 of Figure 1 of Boeing Alert Service Bulletin 767-33A0087, Revision 1, dated September 25, 2003. \n\t(4) For Model 767-400ER series airplanes: Switches identified in step 1 of Figure 1 of Boeing Alert Service Bulletin 767-33A0088, dated December 19, 2001. \n\t(5) For all airplanes: Switches identified for the panel assemblies specified in the applicable service bulletin. \n\nOptional Inspection \n\n\t(i) Instead of doing the inspection required by paragraph (h) of this AD, operators may inspect the part number of the panel assemblies specified in paragraphs (i)(1) and (i)(2) of this AD, as applicable, at the time specified in paragraph (h) of this AD. If the part number is identified as a new part number in paragraph 2.E. "Existing Parts Accountability'' or Appendix B of the applicable service bulletin, no further action is required. If the part number is not identified as a new part number, the inspection required by paragraph (h) of this AD must be done at the specified time. \n\t(1) For switches identified in paragraphs (h)(1), (h)(2), (h)(3), and (h)(4) of this AD: P3-1 and P10 panel assemblies, as applicable. \n\t(2) For switches identified in paragraph (h)(5) of this AD: The panel assemblies identified in the applicable service bulletin. \n\nCorrective Action \n\n\t(j) If during any inspection required by paragraph (h) of this AD, any switch is found that does not have a configuration 'D' switch master module and no switch part number specified in paragraph (j)(1)(i) or (j)(1)(ii) of this AD is found: Before further flight, do the actions specified in either paragraph (j)(1) or (j)(2) of this AD and do the part number revision, as applicable, specified in paragraph (j)(3) of this AD. \n\n\t(1) Replace the switch with a switch specified in paragraph (j)(1)(i), (j)(1)(ii), or (j)(1)(iii) of this AD, in accordance with the applicable service bulletin, except as provided by paragraph (k) of this AD. \n\t(i) Switches having Boeing P/N S231T290-4201 through -4325 inclusive. \n\t(ii) Switches having Korry P/N 4336731004-4201 through -4325 inclusive. \n\n\tNote 3: One-to-one switch correlation between the existing switches and the new part number switches can be found in Korry Service Bulletin 433-33-06, dated November 7, 2001. \n\n\t(iii) Switches that have a configuration 'D' master module. \n\n\t(2) Replace the switch master module with a new configuration 'D' master module in accordance with the applicable service bulletin. \n\n\t(3) If all switches on a panel assembly have a configuration 'D' master module or have a switch partnumber specified in paragraph (j)(1)(i) or (j)(1)(ii) of this AD: Revise the part number of the panel assembly in accordance with the applicable service bulletin. \n\n\t(k) If during any inspection required by paragraph (h) of this AD, a configuration 'D' switch master module is found or the switch part number is specified in paragraph (j)(1)(i) or (j)(1)(ii) of this AD on all switches for a panel assembly: Before further flight, revise the part number of the panel assembly, in accordance with the applicable service bulletin. \n\nContact the FAA/Removal and Installation Procedures \n\n\t(l) If the applicable service bulletin specifies removal or installation of certain parts and does not specify removal or installation instructions: Before further flight, remove or install those parts according to a method approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA, or by doing the actions specified in paragraph (l)(1) of this AD for removal or paragraph (l)(2) of this ADfor installation, as applicable. \n\n\t(1) Remove the module/panel assembly by doing the actions specified in paragraphs (l)(1)(i), (l)(1)(ii), and (l)(1)(iii) of this AD. \n\t(i) Hold the module/panel assembly in position and loosen the quick-release screws. \n\t(ii) Carefully lower the module/panel assembly from the overhead panel. \n\t(iii) Remove the electrical connectors attached to the rear of the module/panel assembly. \n\t(2) Install the module/panel assembly by doing the actions specified in paragraphs (l)(2)(i) and (l)(2)(ii) of this AD. \n\t(i) Make sure that the module/panel assembly is correctly aligned, and connect the electrical connectors to the rear of the unit. \n\t(ii) Carefully lift the module/panel assembly into position and install it with the quick-release screws. \n\nOperational Tests \n\n\t(m) If any panel assemblies, switches, or master modules are replaced during any action required by this AD: Before further flight, do all applicable operational tests in accordancewith the applicable service bulletin, except as provided by paragraph (n) of this AD. \n\n\t(n) Where paragraph 3.B.14.b.(3) of the Accomplishment Instructions of Boeing Alert Service Bulletin 747-33A2280, Revision 1, dated September 25, 2003, specifies procedures to do a test of the engine ignition control/fuel jettison module assembly, this AD requires that operators dry-motor the engine to remove the fuel from the tailpipe before doing the procedures in paragraph 3.B.14.b.(3). All fuel must be removed from the engine tailpipe before performing the test, because during the test the engine igniter will be energized. \n\nActions Accomplished According to Previous Issue of Service Bulletins \n\n\t(o) Actions accomplished before the effective date of this AD in accordance with Boeing Alert Service Bulletin 747-33A2280, 757- 33A0044, 757-33A0045, or 767-33A0087, all dated December 19, 2001, are considered acceptable for compliance with the corresponding action specified in this AD, providedthat the actions specified in this AD are done on the switches for the additional panel assemblies specified in Revision 1 of the service bulletin. \n\nAlternative Methods of Compliance (AMOCs) \n\n\t(p)(1) The Manager, Seattle ACO, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. \n\n\t(2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. \n\nMaterial Incorporated by Reference \n\n\t(q) You must use the service bulletins listed in Table 3 of this AD to perform the actions that are required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approved the incorporation by reference of these documents in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207, for a copy of this service information. You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html . \n\n\tTable 3.--Material Incorporated by Reference \n\n\nBoeing Alert Service Bulletin - \nRevision - \nDated - \n747-33A2280\n1\nSeptember 25, 2003\n757-33A0044\n1\nSeptember 25, 2003\n757-33A0045\n1\nSeptember 25, 2003\n767-33A0087\n1\nSeptember 25, 2003\n767-33A0088, including Appendix A\nOriginal\nDecember 19, 2001

Discussion \n\n\tThe FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 to include an AD that would apply to certain Boeing Model 747-400, -400D, and -400F series airplanes; Boeing Model 757 airplanes; and Boeing Model 767 airplanes. That NPRM was published in the Federal Register on August 16, 2007 (72 FR 45986). That NPRM proposed to require an inspection of certain lighted pushbutton switches in the flight compartment for configuration 'D' master modules and part numbers and corrective action if necessary. That NPRM also provided an option to inspect panel assemblies for part numbers. \n\nComments \n\n\tWe provided the public the opportunity to participate in the development of this AD. We have considered the comments received. \n\nSupport for the NPRM \n\n\tBoeing, the airplane manufacturer, concurs with the content of the NPRM. \n\nRequest To Remove Reference to Revision 1 of the Service Bulletins \n\n\tJapan Airlines requests thatwe remove the reference in the NPRM to Boeing Alert Service Bulletins 747-33A2280 and 767-33A0087, both Revision 1, both dated September 25, 2003 (we referred to those service bulletins as appropriate sources of service information for doing the actions specified in the NPRM). The commenter notes that it has incorporated Boeing Alert Service Bulletins 747-33A2280 and 767- 33A0087, both dated December 19, 2001, for its Model 747-400 and Model 767-200/-300 fleets. The commenter notes that it strictly controls the configuration 'D' master module. However, the commenter states it did not carry out some top assembly module part number changes according to the instructions of Revision 1 of the service bulletins because in some cases the original top assembly module part number was not indicated anywhere, or was indicated unclearly. \n\n\tThe commenter believes that it is impossible to follow the part number change indicated in Revision 1 of the service bulletins and notes that because it tracks the base module, it can ignore the top assembly module part number. \n\n\tThe commenter also states that Boeing agrees that Japan Airlines does not need to perform Revision 1 of the service bulletins because the changes to the bulletin caused by Revision 1 do not affect Japan Airlines' fleet/units. \n\n\tWe disagree with removing the reference to Boeing Alert Service Bulletins 747-33A2280 and 767-33A0087, both Revision 1. We acknowledge that each operator may wish to use different parts and have its own tracking methods. However, we cannot accommodate every operator's differences in each AD. We have determined that the best way to handle such circumstances is for operators to request an alternative method of compliance (AMOC) in accordance with paragraph (p) of this AD, rather than increasing the complexity of the AD by addressing each operator's unique situation. We have not revised this AD in this regard. \n\nConclusion \n\n\tWe have carefully reviewed the available data, includingthe comments received, and determined that air safety and the public interest require adopting the AD as proposed. \n\nCosts of Compliance \n\n\tThere are about 2,511 airplanes of the affected designs in the worldwide fleet. This AD affects about 934 airplanes of U.S. registry. \n\tThe inspection of switches takes about 8 work hours per airplane, at an average labor rate of $80 per work hour. Based on these figures, the estimated cost of the inspection for U.S. operators is $597,760, or $640 per airplane. \n\nAuthority for This Rulemaking \n\n\tTitle 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority. \n\n\tWe are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. \n\nRegulatory Findings \n\n\tWe have determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. \n\n\tFor the reasons discussed above, I certify that this AD: \n\n\t(1) Is not a "significant regulatory action'' under Executive Order 12866; \n\n\t(2) Is not a "significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and \n\n\t(3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. \n\n\tWe prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. See the ADDRESSES section for a location to examine the regulatory evaluation. \n\nList of Subjects in 14 CFR Part 39 \n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. \n\nAdoption of the Amendment \n\nAccordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n\t1. The authority citation for part 39 continues to read as follows: \n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\nSec. 39.13 (Amended) \n\n2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by adding the following new airworthiness directive (AD):