A proposal to amend 14 CFR part 39 to include an AD for the Bell Model 407 helicopters was published in the Federal Register on August 4, 2004 (69 FR 47041). That action proposed to require, before further flight, creating a component history card or equivalent record for each crosstube assembly, converting accumulated run-on landings to an accumulated RIN count, and establishing a retirement life of 5,000 accumulated RIN for the affected crosstube assemblies.
Transport Canada, the airworthiness authority for Canada, notified the FAA that an unsafe condition may exist on Bell Model 407 helicopters. Transport Canada advises that run-on landings impose high stress on landing gear crosstubes, and to prevent possible crosstube failure, the manufacturer has introduced the life limitation of 5,000 RIN. Further evaluation has confirmed the possibility that an extensive training environment with run-on landings may impose high stress on crosstubes. The same condition may result from repetitive landings with forward travel with rotorcraft weight on the skids.
Bell has issued Alert Service Bulletin No. 407-03-59, dated October 15, 2003, which specifies assigning a RIN count to forward and aft crosstube assemblies on Model 407 helicopters. Transport Canada classified this alert service bulletin as mandatory and issued AD No. CF-2004-03, dated February 11, 2004, to ensure the continued airworthiness of these helicopters in Canada.
This helicopter model is manufactured in Canada and is type certificated for operation in the United States under the provisions of 14 CFR 21.29 and the applicable bilateral agreement. Pursuant to the applicable bilateral agreement, Transport Canada has kept the FAA informed of the situation described above. The FAA has examined the findings of Transport Canada reviewed all available information, and determined that AD action is necessary for products of this type design that are certificated for operation inthe United States.
Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were received on the proposal or the FAA's determination of the cost to the public. The FAA has determined that air safety and the public interest require the adoption of the rule as proposed.
The FAA estimates that this AD will affect 319 helicopters of U.S. registry and it will take approximately 4 work hours per helicopter to replace the forward and aft crosstube assemblies at an average labor rate of $65 per work hour. Required parts will cost approximately $6,670 per helicopter for both forward and aft low gear crosstube assemblies, or $8,450 per helicopter for both forward and aft high gear crosstube assemblies. Based on these figures, the total cost impact of this AD on U.S. operators is estimated to be $2,210,670 to replace the low gear crosstube assemblies on the entire fleet or $2,778,490 to replace the high-gear crosstube assemblies onthe entire fleet and assuming the costs associated with creating and updating the historical component card are negligible.
Regulatory Findings
The regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132.
For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final economic evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likelyto exist or develop on products identified in this rulemaking action.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
39.13 [Amended]
2. Section 39.13 is amended by adding a new airworthiness directive to read as follows: