A proposal to amend 14 CFR part 39 to include an AD for the specified model helicopters was published in the Federal Register on November 24, 2003 (68 FR 65854). That action proposed to require removing each tail rotor attachment bushing, part number (P/N) 365A33-3530-20, and then installing a blade-to-torsion bar attachment tuning weight assembly, P/N 365A33-3546-00, on each blade of the Quiet Fenestron tail rotor at the same time. Mixing the existing blade attachment bushings, P/N 365A33-3530-20, and the new tuning weight assembly, P/N 365A33-3546-00, on the same tail rotor hub would be prohibited.
The Direction Generale De L'Aviation Civile (DGAC), the airworthiness authority for France, notified the FAA that an unsafe condition may exist on Eurocopter Model AS 365 N3 helicopters. The DGAC advises of a report of the discovery of an increased level of vibration felt by the crew in the pedal units.
Eurocopter has issued Alert Service Bulletin (ASB)No. 64.00.23, dated October 30, 2002, which specifies installing a tuning weight assembly, P/N 365A33-3546-00, on each blade of the Quiet Fenestron tail rotor. Compliance with this ASB requires prior compliance with Eurocopter Service Bulletin 64.00.21, dated November 8, 2000 (modification 0761B23, 0765B35, and 0764B39, 40, 41), which specifies installing a Quiet Fenestron tail rotor, and with Eurocopter Service Bulletin 65.00.14, dated January 7, 2002 (modification 0765B41), which specifies installing a reinforced control shaft on the tail rotor hub control shaft assembly. The DGAC classified these service bulletins as mandatory and issued AD No. 2002-622(A), dated December 11, 2002, to ensure the continued airworthiness of these helicopters in France.
Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were received on the proposal or the FAA's determination of the cost to the public. The FAA has determined that air safety and the public interest require the adoption of the rule as proposed.
The FAA estimates that this AD will affect 6 helicopters of U.S. registry and the actions will take approximately 8 work hours per helicopter to accomplish at an average labor rate of $65 per work hour. Required parts will cost approximately $3,290, and attaching hardware will cost $40. Based on these figures, we estimate the total cost impact of the AD on U.S. operators to be $3,850 per helicopter, or $23,100 for the entire fleet.
The regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132.
For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
39.13 [Amended]
2. Section 39.13 is amended by adding a new airworthiness directive to read as follows: