Related AD \n\n\tThis AD is related to AD 2002-11-06, amendment 39-12767 (67 FR 38587, June 5, 2002), applicable to certain Boeing Model 777 series airplanes. Boeing Alert Service Bulletin 777-57A0034, Revision 2, dated November 19, 1998; Revision 3, dated May 4, 2000; Revision 4, dated July 20, 2000; and Revision 5, dated January 25, 2001; were referenced as the appropriate sources of service information for accomplishment of the required actions. That AD supersedes AD 2000-19-08, amendment 39- 11909 (65 FR 57282, September 22, 2000), to continue to require repetitive detailed visual inspections to detect cracking of the coveskin on the outboard leading edge slats, and corrective actions, if necessary. AD 2002-11-06 also continues to provide for an optional modification that significantly increases the repetitive inspection interval, and expands the applicability of AD 2000-19-08 by mandating the currently required inspections, and corrective actions, ifnecessary, for additional airplanes. Also, for airplanes on which the optional modification has been accomplished, AD 2002-11-06 requires a new one-time inspection for undersized (incorrect diameter) seal inserts installed in the spanwise bulb seals on certain slats, and replacement of seal assemblies with new assemblies if necessary. \n\nSince the Issuance of That AD \n\n\tSince the issuance of AD 2002-11-06, the FAA has received information from the manufacturer indicating that Group 4 airplanes may have seal assemblies on the outboard leading edge slats on the wings that were installed during production with undersized (incorrect diameter) inserts. In addition, those inserts may have receded into the ends of the seal assemblies. \n\n\tWe also have received reports of the installation of seal assemblies with missing and gapped inserts. These seal assemblies are installed on Model 777 series airplanes on which the seal insert installation was done per Revision 3, 4, 5, or 6 of the referenced service bulletin, and on which the seal inserts were installed during production. Investigation revealed that, during installation, the inserts were stretched and did not return to the original shape before being trimmed and bonded into place. Subsequently, the insert recedes into the ends of the seal assembly, and can become unbonded and detach from the seal assembly. Additionally, when the seal is stretched during installation, the insert can separate at a location along its length which allows the seal to recede from the center of the seal assembly. Such conditions, if not found and fixed, could result in cracking of the slats, subsequent separation of the cove skin, structural damage or loss of the trailing edge wedge, and consequent reduced controllability of the airplane. \n\nExplanation of Relevant Service Information \n\n\tWe have reviewed and approved Boeing Alert Service Bulletin 777- 57A0034, Revision 7, dated May 22, 2003, which describes procedures for inspections ofthe outboard leading edge slats on the wings for installation of seal assemblies with undersized (incorrect diameter) seal inserts and missing or gapped inserts, and follow-on and corrective actions if necessary. The applicable inspections and follow- on and corrective actions are specified in Part 5 and Part 6 of the Work Instructions of the service bulletin, described below: \n\n\tPart 5--Seal Insert Diameter Inspection and Seal Replacement: Describes procedures for airplanes on which the seal insert installation has been done per Part 4 of the service bulletin. (Part 5 was added to Revision 6 of the referenced service bulletin for Groups 1 and 2 airplanes that had done Part 4 of the service bulletin referenced \nin the existing AD.) The procedures specify a one-time inspection of the seal assemblies for correct diameter seal inserts on slat numbers 4, 5, 10, and 11; if the correct diameter insert was installed and the insert has receded into the ends of the seal assembly, install aninsert segment into the ends of the seal assembly; if incorrect diameter seal inserts are installed or the inspection was inconclusive, replace the seal assembly with a new seal assembly. If the correct diameter insert is installed and the insert has not receded into the ends of the seal assembly, no further action is specified for Part 5. \n\n\tPart 6--Seal Insert Gap Inspection and Seal Assembly Replacement: Describes procedures for all airplanes on which the seal insert installation has been done. The procedures specify a one-time inspection of the seal assemblies for missing or gapped inserts. \n\n\tIf the assembly insert is not missing and no gaps are found, the procedures in the service bulletin recommend eventual replacement of the seal assembly with a new seal assembly as specified in Figure 8 of the service bulletin at the time specified in Figure 1 of the service bulletin, regardless of apparent condition. \n\n\tIf the seal assembly insert is missing or gaps are found, the procedures specify doing the following: \n\n\tFor airplanes on which the installation specified in Part 4 has been done: Do a cove skin inspection for cracking as specified in Part 1 of the service bulletin. If no cracking is found, repeat the inspection at the intervals specified. If any cracking is found, the procedures in the service bulletin specify the applicable actions as specified below: \n\nFor any crack that is 1.5 inches in length or less, the follow-on actions include stop-drilling the cracking, doing an internal inspection for cracking as specified in Part 2 of the service bulletin, repairing any cracking found, doing a slat adjustment check, and repeating the cove skin and internal inspections at the intervals specified. \n\nFor any crack that is more than 1.5 inches in length, the follow-on actions include doing an internal inspection for cracking as specified in Part 2 of the service bulletin, repairing any cracking found, doing a slat adjustment check, and repeating the coveskin and internal inspections at the intervals specified. \n\nAs an alternative for all cracks: Replace the slat and do a slat adjustment check, then repeat the cove skin and internal inspections at the intervals specified. \n\n\tIf any cracking exceeds certain limits specified in the 777 Structural Repair Manual, or if internal cracking is found, the service bulletin specifies contacting the manufacturer for repair instructions. \n\n\tFor airplanes on which the seal insert installation was done during production, the procedures also include eventual replacement of the seal assembly with a new seal assembly as specified in Figure 8 of the service bulletin, at the time specified in Figure 1 of the service bulletin, regardless of apparent condition. \n\n\tAccomplishment of the actions specified in the service bulletin is intended to adequately address the identified unsafe condition. \n\nExplanation of the Requirements of the Rule \n\n\tSince an unsafe condition has been identified that islikely to exist or develop on other airplanes of the same type design, this AD is being issued to find and fix discrepancies of the seal assemblies of the outboard leading edge slats on the wings, which could result in cracking of the slats, subsequent separation of the cove skin, structural damage or loss of the trailing edge wedge, and consequent reduced controllability of the airplane. This AD requires inspections of the outboard leading edge slats on the wings for installation of seal assemblies with undersized (incorrect diameter) seal inserts and missing or gapped inserts, and follow-on and corrective actions if necessary. This AD also provides for an optional replacement of the seal assembly in lieu of the inspections. The actions are required to be accomplished in accordance with the service bulletin described previously, except as discussed below. \n\nInterim Action \n\n\tAt this time we are considering a separate rulemaking action to supersede this AD to address the proceduresfor long-term follow-on inspections to find additional cracking, and repair of any cracking found, as described in the service bulletin. Due to the urgency of the need to inspect the fleet and repair any cracking found, this AD will address only the sections in the service bulletin that pertain to the inspections and follow-on and corrective actions specified in Part 5 and Part 6 of the service bulletin. \n\n\tIn addition to superseding this AD, that rulemaking action would also supersede AD 2002-11-06 to mandate replacement of the seal assemblies with new seal assemblies for all 777 series airplanes. However, the planned compliance time for these actions is sufficiently long so that prior notice and time for public comment will be practicable. \n\nDifferences Between This AD and the Service Bulletin \n\n\tThe service bulletin specifies that the manufacturer may be contacted for disposition of certain repair conditions; however, this AD requires the repair of those conditions to be accomplished per a method approved by the FAA, or per data meeting the type certification basis of the airplane approved by a Boeing Company Designated Engineering Representative who has been authorized by the Manager, Seattle Aircraft Certification Office, to make such findings. \n\nClarification of Part Numbers for Installation \n\n\tBoeing Alert Service Bulletin 777-57A0034, Revision 7, dated May 22, 2003, contains certain incorrectly identified part numbers (P/N) in the "Existing Part Number" and "New Part Number" columns of the table under Appendix A, rows 20 and 27 of page 79, and rows 8 and 10 of page 80; respectively. We have been advised that the manufacturer will issue a revision to this alert service bulletin to correct the error. The part numbers are corrected in the tables below: \n\n\tTable: Part Numbers \n\n\nExisting P/N \nName\nCorrect P/N\n114W4140-21\nSlat Assy--No. 11\n114W4140-22\n114W4705-42\nSeal\n114W4705-41 \n\n\t \n\tTable: Part Numbers \n\n\nNew P/N\n Name\nCorrectP/N\n114W4150-23\nSlat Assy--No. 5\n114W4150-29\n114W4150-24\nSlat Assy--No. 10\n114W4150-30\n\nChanges to 14 CFR Part 39/Effect on the AD \n\n\tOn July 10, 2002, the FAA issued a new version of 14 CFR part 39 (67 FR 47997, July 22, 2002), which governs the FAA's airworthiness directives system. The regulation now includes material that relates to altered products, special flight permits, and alternative methods of compliance. Because we have now included this material in part 39, we no longer need to include it in each individual AD; however, this AD identifies the office authorized to approve alternative methods of compliance. \n\nDetermination of Rule's Effective Date \n\n\tSince a situation exists that requires the immediate adoption of this regulation, it is found that notice and opportunity for prior public comment hereon are impracticable, and that good cause exists for making this amendment effective in less than 30 days. \n\nComments Invited \n\n\tAlthough this action is in theform of a final rule that involves requirements affecting flight safety and, thus, was not preceded by notice and an opportunity for public comment, comments are invited on this rule. Interested persons are invited to comment on this rule by submitting such written data, views, or arguments as they may desire. Communications shall identify the Rules Docket number and be submitted in triplicate to the address specified under the caption ADDRESSES. All communications received on or before the closing date for comments will be considered, and this rule may be amended in light of the comments received. Factual information that supports the commenter's ideas and suggestions is extremely helpful in evaluating the effectiveness of the AD action and determining whether additional rulemaking action would be needed. \n\n\tSubmit comments using the following format: \n\nOrganize comments issue-by-issue. For example, discuss a request to change the compliance time and a request to change the service bulletin reference as two separate issues. \nFor each issue, state what specific change to the AD is being requested. \nInclude justification (e.g., reasons or data) for each request. \n\n\tComments are specifically invited on the overall regulatory, economic, environmental, and energy aspects of the rule that might suggest a need to modify the rule. All comments submitted will be available, both before and after the closing date for comments, in the Rules Docket for examination by interested persons. A report that summarizes each FAA-public contact concerned with the substance of this AD will be filed in the Rules Docket. \n\n\tCommenters wishing the FAA to acknowledge receipt of their comments submitted in response to this rule must submit a self-addressed, stamped postcard on which the following statement is made: "Comments to Docket Number 2003-NM-137-AD." The postcard will be date stamped and returned to the commenter. \n\nRegulatory Impact \n\n\tThe regulations adopted herein willnot have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132. \n\n\tThe FAA has determined that this regulation is an emergency regulation that must be issued immediately to correct an unsafe condition in aircraft, and that it is not a "significant regulatory action" under Executive Order 12866. It has been determined further that this action involves an emergency regulation under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979). If it is determined that this emergency regulation otherwise would be significant under DOT Regulatory Policies and Procedures, a final regulatory evaluation will be prepared and placed in the Rules Docket. A copy of it, if filed, may be obtained from the Rules Docket at thelocation provided under the caption ADDRESSES. \n\nList of Subjects in 14 CFR Part 39 \n\n\tAir transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. \n\nAdoption of the Amendment \n\nAccordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows: \n\nPART 39--AIRWORTHINESS DIRECTIVES \n\n1. The authority citation for part 39 continues to read as follows: \n\n\tAuthority: 49 U.S.C. 106(g), 40113, 44701. \n\n§ 39.13 (Amended) \n\n2. Section 39.13 is amended by adding the following new airworthiness directive: