A proposal to amend 14 CFR part 39 to include an AD for BHTC Model 222, 222B, 222U, 230, and 430 helicopters, was published in the Federal Register on April 30, 2002 (67 FR 21185). That action proposed to require removing sealant from the forward tooling hole in the right-hand upper fuel enclosure area.
Transport Canada, the airworthiness authority for Canada, notified the FAA that an unsafe condition may exist on BHTC Model 222, 222B, 222U, 230, and 430 helicopters. Transport Canada advises that a condition exists that can result in an accumulation of fuel in the right-hand upper fuel enclosure area.
BHTC has issued:
Bell Helicopter Textron Alert Service Bulletin (ASB) No. 222-01-89, for Model 222 helicopters, serial numbers (S/N) 47006 through 47089, and Model 222B helicopters, S/N 47131 through 47156;
ASB No. 222U-01-60, for Model 222U helicopters, S/N 47501 through 47574;
ASB No. 230-01-20, for Model 230 helicopters, S/N 23001through 23038; and
ASB No. 430-01-21, for Model 430 helicopters, S/N 49001 through 49079.
All of the ASB's are dated February 7, 2001. All of these ASB's specify procedures for removing the sealant from the existing forward tooling hole located in the panel assembly to provide enclosure drainage. Transport Canada classified these ASB's as mandatory and issued AD No. CF-2001-22, dated May 24, 2001, to ensure the continued airworthiness of these helicopters in Canada.
Interested persons have been afforded an opportunity to participate in the making of this amendment. No comments were received on the proposal or the FAA's determination of the cost to the public. The FAA has determined that air safety and the public interest require the adoption of the rule as proposed, with two changes. The manufacturer's name was incorrectly stated in the notice, and is corrected in this AD. Also, the name of the FAA employee to contact for further information is changed in this AD. TheFAA has determined that these changes will neither increase the economic burden on any operator nor increase the scope of the AD.
The FAA estimates that 151 helicopters of U.S. registry will be affected by this AD, that it will take approximately 5 work hours per helicopter to accomplish the required actions, and that the average labor rate is $60 per work hour. Based on these figures, the total cost impact of the AD on U.S. operators is estimated to be $45,300.
The regulations adopted herein will not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this final rule does not have federalism implications under Executive Order 13132.
For the reasons discussed above, I certify that this action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A final evaluation has been prepared for this action and it is contained in the Rules Docket. A copy of it may be obtained from the Rules Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.
Adoption of the Amendment
Accordingly, pursuant to the authority delegated to me by the Administrator, the Federal Aviation Administration amends part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
39.13 [Amended]2. Section 39.13 is amended by adding a new airworthiness directive to read as follows: